Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Promyde® B30 P2 G40 MI - PA6-GF40 - Nurel S.A.

Material Data Center offers the following functions for Promyde® B30 P2 G40 MI:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Proprietà Specifiche Materiale
Any use of this information falls under the rules of our disclaimer.
Caratteristiche Fisichesecco/condUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 30 / * cm³/10min ISO 1133
Temperatura 275 / * °C -
Carico 5 / * kg -
Proprietà Meccanichesecco/condUnitáNorma del test
ISO Data
Modulo a trazione 11000 / 6200 MPa ISO 527
Resistenza a trazione 170 / 115 MPa ISO 527
Deformazione a rottura 4.5 / 9.5 % ISO 527
Modulo a flessione, 23°C 9500 / 6000 MPa ISO 178
Resistenza all'urto Charpy, +23°C 100 / 130 kJ/m² ISO 179/1eU
Resistenza all'urto Charpy, -30°C 95 / - kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 22 / 40 kJ/m² ISO 179/1eA
Resist. urto Charpy con intaglio, -30°C 17 / - kJ/m² ISO 179/1eA
Proprietà Termichesecco/condUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 222 / * °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 205 / * °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 215 / * °C ISO 75-1/-2
Coeff.di dilatazione termica lin., parallelo 15 / * E-6/K ISO 11359-1/-2
Coeff.di dilatazione termica lin. , perpend. 50 / * E-6/K ISO 11359-1/-2
ASTM Data
UL 94 combustibilitá HB - UL 94
Spessore testati 1.5 mm -
Proprietà Elettrichesecco/condUnitáNorma del test
ISO Data
Costante dielettrica relativa, 1MHz 4 / 5.5 - IEC 62631-2-1
Fattore di dissipazione, 1MHz 230 / 2000 E-4 IEC 62631-2-1
Resistività volumica 1E13 / 1E10 Ohm*m IEC 62631-3-1
Resistività superficiale * / 1E10 Ohm IEC 62631-3-2
Res. Alle correnti striscianti superficiali 500 / 500 - IEC 60112
Altre Proprietàsecco/condUnitáNorma del test
Assorbimento d'acqua 4.9 / * % Sim. alla ISO 62
Assorbimento d'umidità 1.5 / * % Sim. alla ISO 62
Massa volumica 1430 / - kg/m³ ISO 1183
Proprietà Specifiche Materialesecco/condUnitáNorma del test
ISO Data
Numero di viscosità 145 / * cm³/g ISO 307, 1157, 1628
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche speciali
Alto urto o modificato all'urto, Stabilizzato o stabile al calore
Caratteristiche
Stabilità termica
Disponibilità geografica
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.