Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of TPE ProvaMed® 1060 - TPE - ACTEGA DS GmbH

Material Data Center offers the following functions for TPE ProvaMed® 1060:
unit conversion, PDF datasheet print, comparison with other plastics, application examples, CAE Interfaces

Check here, which other Provamed datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di Fluiditá, MFI 8 g/10min ISO 1133
Temperatura 230 °C -
Carico 2.16 kg -
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Carico Unitario al 100% di allungamento 1.7 MPa ISO 527
Allungamento a rottura TPE >300 % ISO 527
Deformazione residua dopo compressione a 23°C, 24h 18 % ISO 815
Deformazione residua dopo compressione a 70°C, 24h 91 % ISO 815
ASTM Data
Durezza A Shore 60 - ASTM D 2240
Durezza D Shore 15 - ASTM D 2240
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 162 °C ISO 11357-1/-3
Temperatura di transizione vetrosa, 10°C/min -40 °C ISO 11357-1/-2
Altre ProprietàValoreUnitáNorma del test
Massa volumica 890 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Temperatura dello stampo 20 - 60 °C -
Temperatura - Zona di Alimentazione 20 - 30 °C -
Zona 1 140 - 230 °C -
Temperatura dell ugello 190 - 230 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione, Altre Estrusioni
Forma fisica disponibile
Pellet
Caratteristiche speciali
Trasparente, Sterilizzabile, Sterilizzazione ad ossido di etilene (EtO), Sterilizzazione a vapore, Gamma irradiation sterilization
Resistenza Chimica
Resistenza all'ossidazione, Resistenza alla radiazione
Certifications
Grado medico, Biocompatibility ISO 10993
Applicazioni
Medicale
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.