Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of THERMOLAST® K TF3CGT - TPE - KRAIBURG TPE GmbH & Co. KG

Material Data Center offers the following functions for THERMOLAST® K TF3CGT:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Thermolast datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Resistenza a trazione 6 MPa ISO 37
Deformazione a rottura 900 % ISO 37
Deformazione residua dopo compressione a 70°C, 24h 27 % ISO 815
Deformazione residua dopo compressione a 100°C, 24h 56 % ISO 815
Resistenza alla lacerazione 10 kN/m ISO 34-1
Durezza Shore A 30 - ISO 7619-1
Altre ProprietàValoreUnitáNorma del test
Massa volumica 880 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 60 - 80 °C -
Pre-essiccamento - Tempo 2 - 4 h -
Temperatura di fusione 200 - 250 °C -
Temperatura dello stampo 25 - 40 °C -
Zona 1 180 - 200 °C -
Zona 2 200 - 220 °C -
Zona 3 220 - 250 °C -
Pressione di Iniezione 20 - 100 MPa -
Contropressione 2 - 10 MPa -
Pressione di chiusura 8 - 60 MPa -
Tempo di residenza, massimo 10 min -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche speciali
Translucent
Caratteristiche
Buona adesione, Soft Feel
Certifications
Contatto con gli alimenti, Approvato per l'utilizzo per contatto con alimenti 10/2011, Approvato per l'utilizzo per contatto con alimenti secondo la FDA 21 CFR
Applicazioni
Imballaggio
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.