Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Topas® ELASTOMER E-140 - COC - Topas Advanced Polymers

Material Data Center offers the following functions for Topas® ELASTOMER E-140:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Topas datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 12 cm³/10min ISO 1133
Temperatura 260 °C -
Carico 2.16 kg -
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 50 MPa ISO 527
Carico unitario a rottura 46 MPa ISO 527
Deformazione a rottura 500 % ISO 527
Resistenza alla lacerazione 47 kN/m ISO 34-1
Durezza Shore A 89 - ISO 7619-1
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 84 °C ISO 11357-1/-3
Temp.di rammollimento Vicat, A 64 °C ISO 306
Altre ProprietàValoreUnitáNorma del test
Massa volumica 940 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Temperatura di fusione 270 - 300 °C -
Temperatura dello stampo 20 - 30 °C -
Temperatura - Zona di Alimentazione <30 °C -
Zona 1 270 - 290 °C -
Zona 2 270 - 300 °C -
Zona 3 275 - 300 °C -
Zona 4 275 - 300 °C -
Temperatura dell ugello 275 - 300 °C -
Velocità di Rotazione della Vite 50 - 100 rpm -
Velocità di iniezione 50 - 150 mm/s -
Pressione di Iniezione 50 - 150 MPa -
Contropressione ≤15 MPa -
Pressione di chiusura 30 - 60 MPa -
Tempo di residenza, massimo <15 min -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche speciali
Trasparente
Caratteristiche
Proprietà di barriera
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.