Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Versollan™ RU 2205-9 - TPU - Avient Corporation

Material Data Center offers the following functions for Versollan™ RU 2205-9:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Versollan datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ASTM Data
Indice di fluidità a caldo, MFI 67 g/10min ASTM D 1238
Temperatura 200 °C -
Carico 5 kg -
Ritiro di stampaggio, parallelo 0.0125 mm/mm ASTM D 955
Proprietà MeccanicheValoreUnitáNorma del test
ASTM Data
Modulo a 100% allungamento 2.62 MPa ASTM D 412
Modulo a 300% allungamento 1.4 MPa ASTM D 412
Durezza A Shore 65 - ASTM D 2240
Resistenza alla lacerazione 47.3 kN/m ASTM D 624
Compressione residua, 22 hr @ 73 °F 34 % ASTM D 395
Resistenza alla trazione a rottura 13.8 MPa ASTM D 412
Allungamento a rottura 710 % ASTM D 412
Altre ProprietàValoreUnitáNorma del test
Densità 1160 kg/m³ ASTM D 792
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 51.7 - 54.4 °C -
Pre-essiccamento - Tempo 3 - 4 h -
Temperatura di fusione 188 - 210 °C -
Temperatura dello stampo 21.1 - 32.2 °C -
Zona 1 168 - 188 °C -
Zona 2 179 - 199 °C -
Zona 3 191 - 210 °C -
Temperatura dell ugello 191 - 216 °C -
Velocità di Rotazione della Vite 75 - 125 rpm -
Velocità di iniezione 12.7 - 50.8 mm/s -
Contropressione 0 - 0.862 MPa -
Pressione di chiusura 0.621 - 1.45 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione, Altre Estrusioni
Forma fisica disponibile
Pellet, Nero
Caratteristiche
Soft Feel
Resistenza Chimica
Resistenza all’olio
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.