Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Bakelite® PF 2774 - PF-(GF+X) - Bakelite Synthetics

Check here, which other Bakelite datasheets, application examples or technical articles are available in Material Data Center

Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Preparazione Provette - Funzioni

Any use of this information falls under the rules of our disclaimer.

Testo del prodotto

Product description:

Phenolic moulding compound, inorganically filled, glass fibre reinforced, increased dimensional stability, average notched impact strength, average heat resistance, improved electrical properties, UL listed moulding compound 1.5 mm / V-0 (ALL).

Application areas:

MCB housings, pump parts, insulating flanges, automotive engine attachments.

Property Name	Value	Unit	Standard No.
Apparent density (moulding compound)	0.75	g/cm³	ISO 60
Moulding shrinkage (injection moulding, longitudinal)	0.4	%	ISO 2577
Post shrinkage (injection moulding, 168h/110°C)	0.2	%	ISO 2577
Moulding shrinkage (compression moulding, longitudinal)	0.25	%	ISO 2577
Post shrinkage (compression moulding, 168h/110°C)	0.1	%	ISO 2577
Tensile strength (5mm/min)	65	MPa	ISO 527-1/2
Compr. strength (test spec. flat tested)	225	MPa	ISO 604
Flexural strength (2mm/min)	110	MPa	ISO 178
Flexural modulus	11000	MPa	ISO 178
Ball indentation hardness (H 961/30)	400	MPa	ISO 2039/P1
Water absorption (24h/23°C)	17	mg	similar to ISO 62

Additional characteristics:

dishwasher proof, low shrinkage/good dimensional stability

Preparation of Test Specimens of Thermosetting Moulding Compound

• Compression to ISO 295
• Injection to ISO 10724

Storage capability
2 years (relative humidity of 50-60% and maximum storage temperature of approximately 20°C)

Caratteristiche Fisiche	Valore	Unitá	Norma del test
ISO Data
Ritiro di stampaggio, parallelo	0.4	%	ISO 294-4, 2577

Proprietà Meccaniche	Valore	Unitá	Norma del test
ISO Data
Modulo a trazione	10000	MPa	ISO 527
Resistenza all'urto Charpy, +23°C	8.5	kJ/m²	ISO 179/1eU
Resistenzia all'urto Charpy con intaglio, +23°C	2.4	kJ/m²	ISO 179/1eA

Proprietà Termiche	Valore	Unitá	Norma del test
ISO Data
Temp.di inflessione sotto caricor, 8.00 MPa	150	°C	ISO 75-1/-2
Reaz. al fuoco spess.nom. 1.5mm	V-0	class	IEC 60695-11-10
Spessore provato	1.5	mm	-
Yellow Card disponibile	sì	-	-

Proprietà Elettriche	Valore	Unitá	Norma del test
ISO Data
Costante dielettrica relativa, 100Hz	7.5	-	IEC 62631-2-1
Fattore di dissipazione, 100Hz	0.15	E-4	IEC 62631-2-1
Resistività volumica	1E10	Ohm*m	IEC 62631-3-1
Resistività superficiale	1E11	Ohm	IEC 62631-3-2
Rigidità dielettrica	26.5	kV/mm	IEC 60243-1
Res. Alle correnti striscianti superficiali	175	-	IEC 60112

Altre Proprietà	Valore	Unitá	Norma del test
Massa volumica	1700	kg/m³	ISO 1183

Preparazione Provette	Valore	Unitá	Norma del test
ISO Data
Stamp. ad Iniezione, temp. della massa d'iniez.	115	°C	ISO 10724
Stamp. ad Iniezione, velocità media d'iniezione	170	mm/s	ISO 10724
Stamp. ad Iniezione, pressione di chiusura	100	MPa	ISO 10724
Stamp. ad Iniezione, tempo di postindurimento	25	min	ISO 10724
Stamp. a Compr., temp. dello stampo	160	°C	ISO 295
Stamp. a Compr., tempo di postindurimento	1	min	ISO 295

Funzioni

Caratteristiche

Processabilità e Forma di Forni

Stampaggio ad Iniezione, Stampaggio a Trasferimento

Disponibilità geografica

Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa

Altre informazioni

Stampaggio ad Iniezione

VERARBEITUNG 

Temperature of material:	80 - 100	°C
Mould temperature:	160 - 190	°C
Curing time:	10-20	sec
Further Information:
Barrel temperature
- Feed zone:	60-75	°C
- Nozzle zone:	80-100	°C
Cavity moulding pressure:	>15	MPa
Back pressure:	0.5-2	MPa
Holding pressure:	60% of injection pressure

Stampaggio a Compressione

PROCESSING

Mould temperature:	160-190	°C
Curing time:	20-40	sec
Cavity moulding pressure:	>15	MPa

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.