Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FORTRON® 4184L6 DW - PPS-(MD+GF)53 - Celanese

Check here, which other Fortron datasheets, application examples or technical articles are available in Material Data Center

Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Funzioni

Any use of this information falls under the rules of our disclaimer.

Testo del prodotto

Fortron 4184L6 is an easier flow version of Fortron 4184L4. for drinking water applications.  It offers similar characteristics to the 4184L4. This grade is especially used for thin walled parts requiring long flow lengths, stiffness and dimensional control. Applications made of this grade are typically electronic components.

Flammability @1.6mm nom. thickn.	V-0	-
Flammability at thickness h (0.75 mm)	V-0	-

Caratteristiche Fisiche	Valore	Unitá	Norma del test
ISO Data
Ritiro di stampaggio, parallelo	0.3	%	ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare	0.6	%	ISO 294-4, 2577
Capacità termica specifica del fuso	1500	J/(kg K)	-

Proprietà Meccaniche	Valore	Unitá	Norma del test
ISO Data
Modulo a trazione	16600	MPa	ISO 527
Carico unitario a rottura	165	MPa	ISO 527
Deformazione a rottura	1.4	%	ISO 527
Resistenza all'urto Charpy, +23°C	29	kJ/m²	ISO 179/1eU
Resistenza all'urto Charpy, -30°C	29	kJ/m²	ISO 179/1eU
Resistenzia all'urto Charpy con intaglio, +23°C	7	kJ/m²	ISO 179/1eA
Resistenzia all'urto Charpy con intaglio, -30°C	7	kJ/m²	ISO 179/1eA

Proprietà Termiche	Valore	Unitá	Norma del test
ISO Data
Temperatura di fusione, 10°C/min	280	°C	ISO 11357-1/-3
Temperatura di transizione vetrosa, 10°C/min	90	°C	ISO 11357-1/-2
Temp.di inflessione sotto carico, 1.80 MPa	270	°C	ISO 75-1/-2
Temp.di inflessione sotto caricor, 8.00 MPa	215	°C	ISO 75-1/-2
Coeff.di dilatazione termica lin., parallelo	24	E-6/K	ISO 11359-1/-2
Coeff.di dilatazione termica lin., perpend.	32	E-6/K	ISO 11359-1/-2
Reaz. al fuoco spess.nom. 1.5mm	V-0	class	IEC 60695-11-10
Spessore provato	1.5	mm	-
Reazione al fuoco a spessore h	V-0	class	IEC 60695-11-10
Spessore provato	0.8	mm	-

Proprietà Elettriche	Valore	Unitá	Norma del test
ISO Data
Costante dielettrica relativa, 1MHz	4.7	-	IEC 62631-2-1
Fattore di dissipazione, 1MHz	20	E-4	IEC 62631-2-1
Resistività volumica	>1E13	Ohm*m	IEC 62631-3-1
Resistività superficiale	>1E15	Ohm	IEC 62631-3-2
Rigidità dielettrica	27	kV/mm	IEC 60243-1

Altre Proprietà	Valore	Unitá	Norma del test
Assorbimento d'acqua	0.02	%	Sim. alla ISO 62
Massa volumica	1800	kg/m³	ISO 1183

Funzioni

Caratteristiche

Processabilità e Forma di Forni

Stampaggio ad Iniezione

Forma fisica disponibile

Pellet

Additivi

Agente di distacco

Caratteristiche speciali

Stabilizzato o stabile alla luce, Stabilizzato o stabile al calore

Altre informazioni

Stampaggio ad Iniezione

Predrying in a dehumidified air dryer at 130 - 140 degC/3-4 hours is recommended.
On injection molding machines with 15-25 D long three-section screws, as are usual in the trade, the FORTRON is processable. A shut-off nozzle is preferred to a free-flow nozzle.

Melt temperature 320-340 degC
Mold wall temperature at least 140 degC

A medium injection rate is normally preferred. All mold cavities must be effectively vented.
Tool temperature of at least 135 degC is recommended for parts to achieve maximum crystallizable potential.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.