Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox. Information about Biopolymers, a project by FH Hannover and M-Base Engineering & Software GmbH sponsored by Fachagentur Nachwachsende Rohstoffe (FNR).

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Inzea® F29 HT 30 - (PLA+PSAC) - Nurel S.A.

Material Data Center offers the following functions for Inzea® F29 HT 30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Inzea datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 4700 MPa ISO 527
Resistenza a trazione 48 MPa ISO 527
Deformazione a snervamento 3 % ISO 527
Deformazione a rottura 5 % ISO 527
Modulo a flessione, 23°C 5000 MPa ISO 178
Resist. urto Charpy con intaglio, +23°C 6.5 kJ/m² ISO 179/1eA
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 177 °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 0.45 MPa 62 °C ISO 75-1/-2
Altre ProprietàValoreUnitáNorma del test
Biobased content 80 % -
Moisture Content 1 % -
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 50 °C -
Temperatura di fusione 200 - 210 °C -
Temperatura dello stampo 100 - 120 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione, Soffiaggio
Caratteristiche speciali
Stabilizzato o stabile al calore
Certifications
Contiene risorse rinnovabili, Biodegradabile, Contatto con gli alimenti, Approvato per l'utilizzo per contatto con alimenti 10/2011, Compostabile ISO 13432 (Produttore), Compostabile ISO 13432 (Certificato)
Disponibilità geografica
Europa, South and Central America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.