Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Maxxam™ VS-693.G001-8009 - PP-GF - Avient Corporation

Material Data Center offers the following functions for Maxxam™ VS-693.G001-8009:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Maxxam datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ASTM Data
Ritiro di stampaggio, parallelo 0.0085 mm/mm ASTM D 955
Proprietà MeccanicheValoreUnitáNorma del test
ASTM Data
Resistenza alla trazione 48 MPa ASTM D 638
Modulo a flessione 2100 MPa ASTM D 790
Resistenza alla flessione 65 MPa ASTM D 790
Resistenza all'urto Izod con intaglio, 1/8 in 350 J/m ASTM D 256
Proprietà TermicheValoreUnitáNorma del test
ASTM Data
UL 94 combustibilitá HB - UL 94
Spessore testati 1.6 mm -
DTUL a 264 psi 100 °C ASTM D 648
Proprietà ElettricheValoreUnitáNorma del test
ASTM Data
Resistenza superficiale 1E15 Ohm ASTM D 257
Altre ProprietàValoreUnitáNorma del test
Densità 1000 kg/m³ ASTM D 792
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 80 - 85 °C -
Pre-essiccamento - Tempo 2 - 3 h -
Temperatura dello stampo 30 - 60 °C -
Zona 1 200 - 240 °C -
Zona 2 200 - 240 °C -
Zona 3 200 - 240 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Nero
Caratteristiche speciali
Alto urto o modificato all'urto
Disponibilità geografica
Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.