Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Promyde® B300 P2 G60 S - PA6-GF60 - Nurel S.A.

Material Data Center offers the following functions for Promyde® B300 P2 G60 S:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caratteristiche Fisichesecco/condUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 35 / * cm³/10min ISO 1133
Temperatura 275 / * °C -
Carico 5 / * kg -
Ritiro di stampaggio, parallelo 0.2 / * % ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare 0.3 / * % ISO 294-4, 2577
Proprietà Meccanichesecco/condUnitáNorma del test
ISO Data
Modulo a trazione 21000 / 17000 MPa ISO 527
Resistenza a trazione 240 / 190 MPa ISO 527
Deformazione a rottura 2.5 / 2.1 % ISO 527
Modulo a flessione, 23°C 19700 / 14400 MPa ISO 178
Resistenza alla flessione 406 / 300 MPa ISO 178
Resistenza all'urto Charpy, +23°C 85 / 110 kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 18 / 25 kJ/m² ISO 179/1eA
Proprietà Termichesecco/condUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 222 / * °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 220 / * °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 220 / * °C ISO 75-1/-2
Coeff.di dilatazione termica lin., parallelo 13 / * E-6/K ISO 11359-1/-2
Coeff.di dilatazione termica lin. , perpend. 50 / * E-6/K ISO 11359-1/-2
Reaz. al fuoco spess.nom. 1.5mm HB / * class IEC 60695-11-10
Spessore provato 1.5 / * mm -
Proprietà Elettrichesecco/condUnitáNorma del test
ISO Data
Res. Alle correnti striscianti superficiali 500 / - - IEC 60112
Other Standards[S]
Resistività volumica 1E13 / 1E11 Ohm*m IEC 60093
Resistività superficiale * / 1E10 Ohm IEC 60093
S: These properties are reported by the producer according standards that are different to our defaults.
Altre Proprietàsecco/condUnitáNorma del test
Assorbimento d'acqua 4.5 / * % Sim. alla ISO 62
Assorbimento d'umidità 1.2 / * % Sim. alla ISO 62
Massa volumica 1690 / - kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura <80 °C -
Pre-essiccamento - Tempo 4 - 6 h -
Temperatura di fusione 235 - 270 °C -
Temperatura dello stampo 40 - 80 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche speciali
Stabilizzato o stabile al calore
Applicazioni
Automotive, Elettrotecnica ed electrici
Disponibilità geografica
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.