Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of SICOFLEX® MZ341 225230 - ABS - Ravago Group

Material Data Center offers the following functions for SICOFLEX® MZ341 225230:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Sicoflex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di Fluiditá, MFI 16 g/10min ISO 1133
Temperatura 220 °C -
Carico 10 kg -
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Carico unitario a trazione 40 MPa ISO 527
Deformazione a rottura 25 % ISO 527
Modulo a flessione, 23°C 2500 MPa ISO 178
Resistenza all'urto Izod con intaglio, +23°C 12 kJ/m² ISO 180/1A
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa 91 °C ISO 75-1/-2
Temp.di rammollimento Vicat, B 97 °C ISO 306
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 80 - 90 °C -
Pre-essiccamento - Tempo 2 - 3 h -
Umidità del Processo ≤0.1 % -
Temperatura di fusione 210 - 240 °C -
Temperatura dello stampo 40 - 60 °C -
Zona 1 205 - 215 °C -
Zona 2 220 - 230 °C -
Zona 3 230 - 240 °C -
Temperatura dell ugello 230 - 235 °C -
Velocità di Rotazione della Vite 40 - 70 rpm -
Contropressione 0.3 - 1.5 MPa -
Pressione di chiusura 3 - 6 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Applicazioni
Polivalente
Disponibilità geografica
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.