Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultradur® B 4300 G4 FC Aqua bk15136 - PBT-GF20 - BASF

Material Data Center offers the following functions for Ultradur® B 4300 G4 FC Aqua bk15136:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultradur datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Testo del prodotto
Ultradur® B 4300 G4 FC Aqua bk15136 is suitable for plastic parts, where material approval regarding drinking water contact and direct food contact is a mandatory requirement.

The product is approved according to
· 21 CFR FDA §177.1660 "Poly(tetramethylene terephthalate)";
· European Food Contact European Food Contact Commission Regulation (EU) 10/2011;
· GMP (EC) N°2023/2006;

and suitable for drinking water contact in accordance with
· KTW-BWGL;
· WRAS (approval);
· ACS (disclosure of ingredients);
· NSF (disclosure of ingredients).

For questions regarding the compliance with further regulations, and certificates, please contact your local BASF representative or Plastics Safety (E-Mail: plastics.safety@basf.com).

The products can also be offered as BMBcert™ and/or Ccycled™. Due to the Massbalance approach the product properties do not change.


Abbreviated designation according to ISO 1043: PBT-GF20
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 16 cm³/10min ISO 1133
Temperatura 250 °C -
Carico 2.16 kg -
Ritiro di stampaggio, parallelo 0.4 % ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare 1.2 % ISO 294-4, 2577
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 7000 MPa ISO 527
Carico unitario a rottura 120 MPa ISO 527
Deformazione a rottura 3.5 % ISO 527
Resistenza all'urto Charpy, +23°C 53 kJ/m² ISO 179/1eU
Resistenza all'urto Charpy, -30°C 47 kJ/m² ISO 179/1eU
Resistenzia all'urto Charpy con intaglio, +23°C 6 kJ/m² ISO 179/1eA
Resistenzia all'urto Charpy con intaglio, -30°C 6 kJ/m² ISO 179/1eA
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 223 °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 195 °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 220 °C ISO 75-1/-2
Coeff.di dilatazione termica lin., parallelo 35 E-6/K ISO 11359-1/-2
Coeff.di dilatazione termica lin., perpend. 125 E-6/K ISO 11359-1/-2
Reaz. al fuoco spess.nom. 1.5mm HB class IEC 60695-11-10
Spessore provato 1.5 mm -
Yellow Card disponibile - -
Yellow Card disponibile - -
Indice di ossigeno 19.5 % ISO 4589-1/-2
Proprietà ElettricheValoreUnitáNorma del test
ISO Data
Fattore di dissipazione, 100Hz 23 E-4 IEC 62631-2-1
Fattore di dissipazione, 1MHz 190 E-4 IEC 62631-2-1
Resistività superficiale >1E15 Ohm IEC 62631-3-2
Rigidità dielettrica 37 kV/mm IEC 60243-1
Res. Alle correnti striscianti superficiali 275 - IEC 60112
Altre ProprietàValoreUnitáNorma del test
Assorbimento d'acqua 0.4 % Sim. alla ISO 62
Assorbimento d'umidità 0.2 % Sim. alla ISO 62
Massa volumica 1450 kg/m³ ISO 1183
Proprietà Specifiche MaterialeValoreUnitáNorma del test
ISO Data
Numero di viscosità 105 cm³/g ISO 307, 1157, 1628
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 80 - 120 °C -
Pre-essiccamento - Tempo 4 h -
Umidità del Processo ≤0.04 % -
Temperatura di fusione 250 - 275 °C -
Temperatura dello stampo 60 - 100 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet, Nero
Additivi
Lubrificanti
Caratteristiche speciali
Stabilizzato o stabile alla luce, Estab. agli U.V. o per applicaz.in esterni, Stabilizzato o stabile al calore
Certifications
Contatto con gli alimenti, Approvato per l'utilizzo per contatto con alimenti 10/2011, Approvato per l'utilizzo per contatto con alimenti secondo la FDA 21 CFR, Contatto con acqua potabile, Contacto con acqua potabile KTW, Contatto con acqua potabile DVGW W270, Contatto con acqua potabile NSF 61
Disponibilità geografica
Altre informazioni
Stampaggio ad Iniezione
PREPROCESSING
Pre/Post-processing, max. allowed water content: .04 %
Pre/Post-processing, Pre-drying, Temperature: 80 - 120 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 250 - 275 °C
injection molding, Melt temperature, recommended: 260 °C
injection molding, Mold temperature, range: 60 - 100 °C
injection molding, Mold temperature, recommended: 80 °C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.