Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Vitane LFC 9350 - TPU - geba Kunststoffcompounds GmbH

Material Data Center offers the following functions for Vitane LFC 9350:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Vitane datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Proprietà Elettriche - Altre Proprietà - Preparazione Provette - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Resistenza a trazione 15.5 MPa ISO 37
Deformazione a rottura 130 % ISO 37
Durezza Shore D 50 - ISO 7619-1
Other Standards[S]
Carico Unitario al 10% di allungamento 0.7 MPa DIN 53504
S: These properties are reported by the producer according standards that are different to our defaults.
Proprietà ElettricheValoreUnitáNorma del test
Other Standards[S]
Resistività volumica 2 Ohm*m IEC 60093
Resistività superficiale 400 Ohm IEC 60093
S: These properties are reported by the producer according standards that are different to our defaults.
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1270 kg/m³ ISO 1183
Preparazione ProvetteValoreUnitáNorma del test
ISO Data
Stamp. ad Iniezione, temp. di fusione 220 °C ISO 294
Stamp. ad Iniezione, temperatura dello stampo 60 °C ISO 294
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura <80 °C -
Pre-essiccamento - Tempo 4 - 6 h -
Umidità del Processo ≤0.02 % -
Temperatura di fusione 210 - 230 °C -
Temperatura dello stampo 40 - 80 °C -
Temperatura - Zona di Alimentazione 60 - 80 °C -
Zona 1 210 - 220 °C -
Zona 2 210 - 220 °C -
Zona 3 220 - 230 °C -
Temperatura dell ugello 220 - 230 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche speciali
Migliorata conduttività elettrica
Resistenza Chimica
Resistenza all’olio
Applicazioni
Elettrotecnica ed electrici, Imballaggio
Disponibilità geografica
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.