Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FORTRON® 0214 - PPS - Celanese

Check here, which other Fortron datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - Processing Recommendation Injection Molding - 機能

Any use of this information falls under the rules of our disclaimer.

Processing/Physical Characteristics	値	単位	テスト基準
ISO データ
成形収縮率, 平行	1.2	%	ISO 294-4, 2577
成形収縮率, 直角	1.5	%	ISO 294-4, 2577
溶融時の密度	1150	kg/m³	-
溶融時の比熱	1830	J/(kg K)	-

機械的特性	値	単位	テスト基準
ISO データ
引張弾性率	3800	MPa	ISO 527
破壊応力	90	MPa	ISO 527
破壊ひずみ	3	%	ISO 527

熱的特性	値	単位	テスト基準
ISO データ
溶融温度, 10°C/min	280	°C	ISO 11357-1/-3
ガラス転移点, 10°C/min	90	°C	ISO 11357-1/-2
荷重たわみ温度, 1.80 MPa	110	°C	ISO 75-1/-2
荷重たわみ温度, 8.00 MPa	95	°C	ISO 75-1/-2
線膨張係数, 平行	52	E-6/K	ISO 11359-1/-2
線膨張係数, 直角	53	E-6/K	ISO 11359-1/-2

電気的特性.	値	単位	テスト基準
ISO データ
体積抵抗率	1E9	Ohm*m	IEC 62631-3-1
耐電圧	18	kV/mm	IEC 60243-1

その他の特性.	値	単位	テスト基準
吸水率	0.02	%	Sim. to ISO 62
密度	1350	kg/m³	ISO 1183

Processing Recommendation Injection Molding	値	単位	テスト基準
Pre-drying - Temperature	120	°C	-
Pre-drying - Time	3 - 4	h	-
樹脂温度	310 - 320	°C	-
金型温度	≥140	°C	-

機能

特殊な特性

成形加工法.

射出成形., フィルム押出成形., シート押出成形., その他の押出成形.

納入形状.

ペレット., パウダー.

領域別の利用可能性

北アメリカ., ヨーロッパ., 南・中央アメリカ., 近東/アフリカ

その他の情報

村遜速揃

In spite of the minimum moisture absorption a drying of FORTRON is necessary. Predrying in a dehumidified air dryer at 120 degC/3-4 hours is recommended.
On injection molding machines with 15-25 D long three-section screws, are usual in the trade, the unreinforced FORTRON is processable. A shut-off nozzle is recommended.

Melt temperature 310-320 degC
Mold wall temperature at least 140 degC

A medium injection rate is normally preferred. All mold cavities must be effectively vented.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.