Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of KEBAFORM C 902 XFA - POM - Barlog plastics GmbH

Material Data Center offers the following functions for KEBAFORM C 902 XFA:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Kebaform datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics値単位テスト基準
ISO データ
メルトフローレート, MFI 9 g/10min ISO 1133
温度 190 °C -
荷重 2.16 kg -
成形収縮率, 平行 2.0 % ISO 294-4, 2577
成形収縮率, 直角 2.0 % ISO 294-4, 2577
機械的特性値単位テスト基準
ISO データ
引張弾性率 2700 MPa ISO 527
降伏応力 60 MPa ISO 527
降伏ひずみ 11 % ISO 527
破壊ひずみ 40 % ISO 527
シャルピー衝撃強さ, +23°C 100 kJ/m² ISO 179/1eU
ノッチ付きシャルピー衝撃強さ, +23°C 7 kJ/m² ISO 179/1eA
熱的特性値単位テスト基準
ISO データ
溶融温度, 10ﾟC/min 170 °C ISO 11357-1/-3
荷重たわみ温度, 1.80 MPa 93 °C ISO 75-1/-2
線膨張係数, 平行 120 E-6/K ISO 11359-1/-2
線膨張係数, 直角 120 E-6/K ISO 11359-1/-2
厚さhでの燃焼性 HB class IEC 60695-11-10
試験片の厚さ 0.8 mm -
電気的特性.値単位テスト基準
ISO データ
体積抵抗率 1E16 Ohm*m IEC 62631-3-1
表面抵抗率 1E16 Ohm IEC 62631-3-2
耐電圧 19 kV/mm IEC 60243-1
その他の特性.値単位テスト基準
吸水率. 0.22 % Sim. to ISO 62
密度. 1410 kg/m³ ISO 1183
Processing Recommendation Injection Molding値単位テスト基準
Pre-drying - Temperature 80 °C -
Pre-drying - Time 3 - 5 h -
Processing humidity ≤0.1 % -
金型温度 60 - 120 °C -
Feed temperature 60 - 80 °C -
Zone 1 180 - 220 °C -
特殊な特性
成形加工法.
射出成形.
特殊な特性.
紫外線安定化.
な特性
Low Emission, Tribologic Grade, Copolymer
耐薬品性
General Chemical Resistance
アプリケーション
自動車, カプセル化された
領域別の利用可能性
ヨーロッパ.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.