Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Teflon™ PFA 416HP - PFA - The Chemours Company

Material Data Center offers the following functions for Teflon™ PFA 416HP:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Teflon datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性.
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics値単位テスト基準
Other Standards[S]
メルトフローレイト, MFI 42 g/10min ASTM D 3307
S: These properties are reported by the producer according standards that are different to our defaults.
機械的特性値単位テスト基準
ASTM数据
曲げ弾性率 690 MPa ASTM D 790
ショア硬さD 55 - ASTM D 2240
Other Standards[S]
引張強度 25 MPa ASTM D 3307
破断伸び 350 % ASTM D 3307
S: These properties are reported by the producer according standards that are different to our defaults.
熱的特性値単位テスト基準
ASTM数据
UL94 燃焼性 V-0 - UL 94
酸素指数 95 % ASTM D 2863
Other Standards[S]
溶融温度 305 °C ASTM D 4591
Max. Service Temp., Continous 260 °C -
S: These properties are reported by the producer according standards that are different to our defaults.
電気的特性.値単位テスト基準
ASTM数据
耐電圧, 短い時間 80 kV/mm ASTM D 149
誘電正接, 1 MHz 0.0002 - ASTM D 150
比誘電率, 1 MHz 2.03 - ASTM D 150
体積抵抗率 1E18 Ohm*cm ASTM D 257
その他の特性.値単位テスト基準
吸水率, 24hr 0.03 % ASTM D 570
密度 2150 kg/m³ ASTM D 792
特殊な特性
成形加工法.
射出成形., その他の押出成形., コーティング., トランスファー成形., Compression Molding
納入形状.
ペレット.
特殊な特性.
紫外線安定化., 熱安定化.
な特性
Good Drawdown, Low Smoke, Melt Strength, Thermal Stability, Tribologic Grade
耐薬品性
General Chemical Resistance, Environmental Stress Crack Resistance
Certifications
Food contact, Food approval 10/2011, Food approval FDA 21 CFR
アプリケーション
電気電子
領域別の利用可能性
北アメリカ., ヨーロッパ., アジア/太平洋地域., 南・中央アメリカ.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.