Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VECTRA® MT®4310 - LCP-GF30 - Celanese

Check here, which other Vectra datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - 機能

Any use of this information falls under the rules of our disclaimer.

商品の説明文

Vectra^® MT4310 VF3001 (natural) is a 30% glass reinforced high flow, LCP grade for injection molding.

Vectra^® MT4310 VF3001 (natural) is a special grade developed for medical industry applications and complies with:

• Food Contact Substance Notification (FCN) No. 742 of the Food and Drug Administration (FDA) and is listed in the Drug Master File (DMF 8464) and the Device Master File (MAF 315)
• the corresponding EU and national registry regulatory requirements
• biocompatibility in tests corresponding to USP 23 Class VI/ISO 10993
• low residual monomers
• no animal products

Highest temperature capability
Easiest flow
Suitable where very thin walls are required
Used for broad range of SMT applications, with minimal dimensional change
Chemical abbreviation according to ISO 1043-1 : LCP
Inherently flame retardant

Flammability at thickness h

V-0

-

Processing/Physical Characteristics	値	単位	テスト基準
ISO データ
成形収縮率, 平行	0.1	%	ISO 294-4, 2577
成形収縮率, 直角	0.5	%	ISO 294-4, 2577

機械的特性	値	単位	テスト基準
ISO データ
引張弾性率	16000	MPa	ISO 527
破壊応力	160	MPa	ISO 527
破壊ひずみ	1.6	%	ISO 527
ノッチ付きシャルピー衝撃強さ, +23°C	40	kJ/m²	ISO 179/1eA

熱的特性	値	単位	テスト基準
ISO データ
溶融温度, 10°C/min	335	°C	ISO 11357-1/-3
荷重たわみ温度, 1.80 MPa	276	°C	ISO 75-1/-2
荷重たわみ温度, 8.00 MPa	216	°C	ISO 75-1/-2
ビカット軟化温度, B	195	°C	ISO 306
線膨張係数, 平行	7	E-6/K	ISO 11359-1/-2
線膨張係数, 直角	20	E-6/K	ISO 11359-1/-2
厚さhでの燃焼性	V-0	class	IEC 60695-11-10
酸素指数	45	%	ISO 4589-1/-2

電気的特性.	値	単位	テスト基準
ISO データ
比誘電率, 100Hz	4	-	IEC 62631-2-1
比誘電率, 1MHz	3.3	-	IEC 62631-2-1
誘電正接, 100Hz	100	E-4	IEC 62631-2-1
誘電正接, 1MHz	250	E-4	IEC 62631-2-1
体積抵抗率	1E13	Ohm*m	IEC 62631-3-1
表面抵抗率	1E14	Ohm	IEC 62631-3-2
耐電圧	32	kV/mm	IEC 60243-1

その他の特性.	値	単位	テスト基準
密度	1610	kg/m³	ISO 1183

機能

特殊な特性

成形加工法.

射出成形.

納入形状.

ペレット., ナチュラルカラー

特殊な特性.

難燃., 光安定化., 滅菌可能, エチレンオキシド滅菌(EtO), 蒸気滅菌, Gamma irradiation sterilization

Certifications

Food contact, Food approval BfR, Food approval FDA 21 CFR, Food contact notification (FCN), Medical Grade, Biocompatibility ISO 10993, US Pharmacopeia Class VI Approved, Drug Master File, Device Master File

アプリケーション

医療の

領域別の利用可能性

北アメリカ., ヨーロッパ.

その他の情報

村遜速揃

Vectra resins are well known for their excellent thermal and hydrolytic stability. In order to ensure these properties are optimum, the resin should be dried correctly prior to processing. Vectra LCP MT4310 and MT4350 should be dried at 150°C for a minimum of 6 hours or at 170°C for a minimum of 4 hours in a desiccant dryer.
A three-zone screw evenly divided into feed, compression, and metering zones is preferred. A higher percentage of feed flights may be needed for smaller machines: 1/2 feed, 1/4 compression, 1/4 metering.

Vectra LCPs are shear thinning, their melt viscosity decreases quickly as shear rate increases. For parts that are difficult to fill, the molder can increase the injection velocity to improve melt flow.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.