Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Badalac® ABS 20 GF30 - ABS-GF30 - Bada AG

Material Data Center offers the following functions for Badalac® ABS 20 GF30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Badalac datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 4 cm³/10min ISO 1133
온도 220 °C -
하중 10 kg -
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 8800 MPa ISO 527
파단시 강도 90 MPa ISO 527
파단시 신율 1.7 % ISO 527
챠피 충격 강도, +23°C 35 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 9 kJ/m² ISO 179/1eA
열적 특성값단위시험규격
ISO 데이터
비카트 연화 온도, A 107 °C ISO 306
두께 H인 제품의 난연성 HB class IEC 60695-11-10
테스트 두께 0.8 mm -
전기적 특성값단위시험규격
ISO 데이터
상대 유전뮬, 1MHz 2.8 - IEC 62631-2-1
소산 인자, 1MHz 79 E-4 IEC 62631-2-1
부피 저항 1E11 Ohm*m IEC 62631-3-1
표면 저항 1E13 Ohm IEC 62631-3-2
전기 압력 37 kV/mm IEC 60243-1
기타 특성값단위시험규격
물에서의 흡수성 0.7 % ISO 62와 유사
조건에서의 흡습성 0.2 % ISO 62와 유사
밀도 1230 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 80 °C -
Pre-drying - Time 2 - 4 h -
Processing humidity ≤0.1 % -
용융수지온도 220 - 260 °C -
성형온도 30 - 80 °C -
특징
생산 공정
사출 성형
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.