Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of CELANEX® 6035GB20 - PBT-GB20 - Celanese

Material Data Center offers the following functions for CELANEX® 6035GB20:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Celanex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
성형 수축률, 평행 1.5 % ISO 294-4, 2577
성형 수축률, 수직 1.5 % ISO 294-4, 2577
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 3300 MPa ISO 527
파단시 강도 46 MPa ISO 527
파단시 신율 8.5 % ISO 527
챠피 충격 강도 , +23°C 22 kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C 19 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 1.7 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 2.8 kJ/m² ISO 179/1eA
쇼어 D 경도 80 - ISO 7619-1
열적 특성값단위시험규격
ISO 데이터
녹는점, 10°C/min 225 °C ISO 11357-1/-3
유리 전이 온도, 10 °C/min 50 °C ISO 11357-1/-2
하중하에서의 변형온도, 1.80 MPa 72 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 168 °C ISO 75-1/-2
선형 열팽창 계수, 평행 77 E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 77 E-6/K ISO 11359-1/-2
전기적 특성값단위시험규격
ISO 데이터
상대 유전율, 100Hz 3.7 - IEC 62631-2-1
상대 유전뮬, 1MHz 3.5 - IEC 62631-2-1
소산 인자, 1MHz 170 E-4 IEC 62631-2-1
부피 저항 >1E13 Ohm*m IEC 62631-3-1
표면 저항 >1E15 Ohm IEC 62631-3-2
전기 압력 30 kV/mm IEC 60243-1
기타 특성값단위시험규격
조건에서의 흡습성 0.19 % ISO 62와 유사
밀도 1460 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 121 °C -
Pre-drying - Time 4 h -
Processing humidity ≤0.02 % -
용융수지온도 235 - 260 °C -
성형온도 65 - 93 °C -
특징
생산 공정
사출 성형
인도 유형
펠렛 (입자,알갱이)
기타 정보
사E성
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30°F (-34°C) at 250°F (121°C) for 4 hours.
Rear Temperature 450-470(230-240) deg F (deg C)
Center Temperature 460-480(235-250) deg F (deg C)
Front Temperature 470-500(240-260) deg F (deg C)
Nozzle Temperature 480-500(250-260) deg F (deg C)
Melt Temperature 460-500(235-260) deg F (deg C)
Mold Temperature 150-200(65-93) deg F (deg C)
Back Pressure 0-50 psi
Screw Speed Medium
Injection Speed Fast

Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.