Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LARPEEK 50 G/30 - PEEK-GF - LATI Industria Termoplastici S.p.A.

Material Data Center offers the following functions for LARPEEK 50 G/30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Larpeek datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
성형 수축률, 평행 0.4 % ISO 294-4, 2577
성형 수축률, 수직 0.8 % ISO 294-4, 2577
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 11500 MPa ISO 527
파단시 강도 175 MPa ISO 527
파단시 신율 2.2 % ISO 527
챠피 충격 강도, +23°C 70 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 10 kJ/m² ISO 179/1eA
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 300 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 300 °C ISO 75-1/-2
비카트 연화 온도, B 300 °C ISO 306
선형 열팽창 계수, 평행 20 E-6/K ISO 11359-1/-2
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 2 mm -
Glow Wire Ignition Temperature (GWIT) 875 °C IEC 60695-2-13
GWIT - thickness tested (1) 1 mm -
ASTM 데이터
UL94 난연성 V-1 - UL 94
테스트 두께 0.75 mm -
산소지수 36 % ASTM D 2863
전기적 특성값단위시험규격
ASTM 데이터
표면 저항 1E12 Ohm ASTM D 257
기타 특성값단위시험규격
밀도 1500 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 120 - 150 °C -
Pre-drying - Time 3 h -
용융수지온도 370 - 400 °C -
성형온도 170 - 200 °C -
특징
생산 공정
사출 성형
특성
Low Smoke
내화학성에
General Chemical Resistance
지역별 검색
짱쨌쨈
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.