Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox. Information about Biopolymers, a project by FH Hannover and M-Base Engineering & Software GmbH sponsored by Fachagentur Nachwachsende Rohstoffe (FNR).

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Makrolon® 6265 X RE - PC - Covestro Deutschland AG

Material Data Center offers the following functions for Makrolon® 6265 X RE:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Makrolon datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 테스트 견본 생산 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 19 cm³/10min ISO 1133
온도 300 °C -
하중 1.2 kg -
용융 흐름성, MFI 20 g/10min ISO 1133
온도 300 °C -
负荷 1.2 kg -
성형 수축률, 평행 0.7 % ISO 294-4, 2577
성형 수축률, 수직 0.7 % ISO 294-4, 2577
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 2400 MPa ISO 527
항복강도 65 MPa ISO 527
항복변형률 6 % ISO 527
파단시 평균신율 >50 % ISO 527
파단시 강도 65 MPa ISO 527
파단시 신율 120 % ISO 527
굴곡 계수, 23°C 2400 MPa ISO 178
굴곡 강도 96 MPa ISO 178
탄성변형률, 1h 2200 MPa ISO 899-1
탄성변형률, 1000h 1900 MPa ISO 899-1
챠피 충격 강도, +23°C N kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 65 kJ/m² ISO 179/1eA
Type of failure P(C) - -
챠피 노치드 충격 강도, -30°C 12 kJ/m² ISO 179/1eA
Type of failure C - -
아이조드 충격은 노치, +23°C 50 kJ/m² ISO 180/1A
아이조드 충격은 노치 11 kJ/m² ISO 180/1A
온도 -30 °C -
최대 관통힘, +23°C 5000 N ISO 6603-2
최대 관통힘, -30°C 5900 N ISO 6603-2
관통 에너지, +23°C 50 J ISO 6603-2
관통 에너지, -30°C 55 J ISO 6603-2
Ball indentation hardness 115 MPa ISO 2039-1
열적 특성값단위시험규격
ISO 데이터
유리 전이 온도, 10 °C/min 144 °C ISO 11357-1/-2
하중하에서의 변형온도, 1.80 MPa 124 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 137 °C ISO 75-1/-2
비카트 연화 온도, B 145 °C ISO 306
선형 열팽창 계수, 평행 65 E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 65 E-6/K ISO 11359-1/-2
1.5mm 평균두께에서의 난연성 V-0 class IEC 60695-11-10
테스트 두께 1.5 mm -
Yellow Card 유효한 예 - -
산소지수로서의 난연성 36 % ISO 4589-1/-2
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 0.75 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (2) 1.5 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (3) 3 mm -
Glow Wire Ignition Temperature (GWIT) 875 °C IEC 60695-2-13
GWIT - thickness tested (1) 0.75 mm -
Glow Wire Ignition Temperature (GWIT) 900 °C IEC 60695-2-13
GWIT - thickness tested (2) 1.5 mm -
Glow Wire Ignition Temperature (GWIT) 900 °C IEC 60695-2-13
GWIT - thickness tested (3) 3 mm -
Other Standards[S]
열전도율, 솔리드 0.2 W/(m K) ISO 8302
S: These properties are reported by the producer according standards that are different to our defaults.
전기적 특성값단위시험규격
ISO 데이터
전기 압력 34 kV/mm IEC 60243-1
CTI 225 - IEC 60112
Other Standards[S]
상대 유전율, 100Hz 3.1 - IEC 60250
상대 유전뮬, 1MHz 3 - IEC 60250
소산 인자, 100Hz 8 E-4 IEC 60250
소산 인자, 1MHz 90 E-4 IEC 60250
부피 저항 1E14 Ohm*m IEC 60093
표면 저항 1E16 Ohm IEC 60093
S: These properties are reported by the producer according standards that are different to our defaults.
기타 특성값단위시험규격
물에서의 흡수성 0.3 % ISO 62와 유사
조건에서의 흡습성 0.12 % ISO 62와 유사
밀도 1200 kg/m³ ISO 1183
Bulk density 640 kg/m³ -
테스트 견본 생산값단위시험규격
ISO 데이터
사출성형: 용융수지온도 280 °C ISO 294
사출성형: 금형온도 80 °C ISO 294
사출성형: 사출속도 200 mm/s ISO 294
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 120 °C -
Pre-drying - Time 2 - 3 h -
Processing humidity ≤0.02 % -
용융수지온도 280 - 320 °C -
성형온도 80 - 120 °C -
Zone 1 250 - 260 °C -
Zone 2 270 - 280 °C -
Zone 3 280 - 290 °C -
Nozzle temperature 290 - 300 °C -
Back pressure 5 - 15 MPa -
특징
생산 공정
사출 성형
부가물
이형제
특별 특성
난연성, Opaque
Certifications
Contains renewable resources, ISCC Plus
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.