Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Pebax® MV 1074 SA 01 - TPA - ARKEMA

Material Data Center offers the following functions for Pebax® MV 1074 SA 01:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Pebax datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 기계적 성질 (필름)
Any use of this information falls under the rules of our disclaimer.
제품 설명서
Polyether block amide Pebax® MV 1074 SA 01 resin is a thermoplastic elastomer made of flexible and hydrophilic polyether and rigid polyamide.
Pebax® MV 1074 SA 01 resin is also an inherently dissipative polymer and can be dry blended or compounded with a polymer matrix to lower the surface resistivity of the final part.
This hydrophilic grade when extruded into either a thin film or laminated  on to a substrate offers excellent permeability to moisture vapor while remaining waterproof .
This SA grade is specially designed to food uses.

Refractive index according to an internal method is 1.502.

Main applications:
  • Breathable membranes
  • Permanent antistactic additive
  • Note: this grade is not recommended by Arkema for usage in medical applications. For such applications Pebax® SA 01 MED should be used


Packaging:
This grade is delivered dried in sealed packaging (25 kg bags and 550 kg rigid containers) ready to be processed.

Shelf Life:
Two years from the delivery. For any use above this limit, please refer to our technical services.
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 97 / 80 MPa ISO 527
50%변형하에서의 강도 10 / 10 MPa ISO 527
파단시 신율 >50 / >50 % ISO 527
파단시 강도 TPE 30 / * MPa ISO 527
파단시 신율 TPE >300 / * % ISO 527
쇼어 D 경도 38 / * - ISO 7619-1
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 158 / * °C ISO 11357-1/-3
유리 전이 온도, 10 °C/min -40 / * °C ISO 11357-1/-2
산소지수로서의 난연성 19 / * % ISO 4589-1/-2
전기적 특성건조/응축단위시험규격
ISO 데이터
부피 저항 1.5E9 / 2.5E7 Ohm*m IEC 62631-3-1
표면 저항 * / 3E9 Ohm IEC 62631-3-2
전기 압력 5 / - kV/mm IEC 60243-1
기타 특성건조/응축단위시험규격
조건에서의 흡습성 1.4 / * % ISO 62와 유사
밀도 1070 / - kg/m³ ISO 1183
기계적 성질 (필름) 건조/응축단위시험규격
ISO 데이터
최대강도, 평행 32 / * MPa ISO 527-3
최대강도, 수직 34 / * MPa ISO 527-3
최대변형율, 평행 500 / * % ISO 527-3
최대변형율, 수직 700 / * % ISO 527-3
특징
생산 공정
사출 성형, 기타 압출
인도 유형
펠렛 (입자,알갱이)
특별 특성
정전기 방지, 가시광선 안정성, 열안정성
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
기타 정보
사E성

Processing conditions:

- Typical melt temperature (Min / Recommended / Max): 200°C / 240°C / 270°C.
- Typical mold temperature: 25–60°C.
- Drying time and temperature (only necessary for bags opened for more than two hours): 4-6 hours at 65-75°C.
기타 압출

Processing conditions:

- Typical melt temperature (Min / Recommended / Max): 210°C / 220°C / 230°C.
- Drying time and temperature (only necessary for bags opened for more than two hours): 4-6 hours at 65-75°C.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.