Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of Promyde® B30 P2 HI60 - PA6 - Nurel S.A.
Material Data Center offers the following functions for Promyde® B30 P2 HI60:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our
disclaimer.
| Processing/Physical Characteristics | 건조/응축 | 단위 | 시험규격 |
| ISO 데이터 |
| 용융 부피 - 흐름 속도, MVR |
120 / * |
cm³/10min |
ISO 1133 |
| 온도 |
275 / * |
°C |
- |
| 하중 |
5 / * |
kg |
- |
| 성형 수축률, 평행 |
0.8 / * |
% |
ISO 294-4, 2577 |
| 성형 수축률, 수직 |
0.8 / * |
% |
ISO 294-4, 2577 |
| 기계적 특성 | 건조/응축 | 단위 | 시험규격 |
| ISO 데이터 |
| 인장탄성률 |
2100 / 1300 |
MPa |
ISO 527 |
| 인장 강도 |
60 / 35 |
MPa |
ISO 527 |
| 항복변형률 |
4.5 / 35 |
% |
ISO 527 |
| 파단시 신율 |
35 / >50 |
% |
ISO 527 |
| 굴곡 계수, 23°C |
1700 / 900 |
MPa |
ISO 178 |
| 굴곡 강도 |
70 / 35 |
MPa |
ISO 178 |
| 챠피 충격 강도, +23°C |
N / N |
kJ/m² |
ISO 179/1eU |
| 챠피 충격 강도, -30°C |
N / - |
kJ/m² |
ISO 179/1eU |
| 챠피 노치드 충격 강도, +23°C |
65 / 125 |
kJ/m² |
ISO 179/1eA |
| 챠피 노치드 충격 강도, -30°C |
20 / - |
kJ/m² |
ISO 179/1eA |
| 열적 특성 | 건조/응축 | 단위 | 시험규격 |
| ISO 데이터 |
| 녹는점, 10°C/min |
222 / * |
°C |
ISO 11357-1/-3 |
| 하중하에서의 변형온도, 1.80 MPa |
50 / * |
°C |
ISO 75-1/-2 |
| 선형 열팽창 계수, 평행 |
120 / * |
E-6/K |
ISO 11359-1/-2 |
| 선형 열팽창 계수, 수직 |
120 / * |
E-6/K |
ISO 11359-1/-2 |
| 1.5mm 평균두께에서의 난연성 |
HB / * |
class |
IEC 60695-11-10 |
| 테스트 두께 |
1.5 / * |
mm |
- |
| 전기적 특성 | 건조/응축 | 단위 | 시험규격 |
| ISO 데이터 |
| CTI |
600 / - |
- |
IEC 60112 |
| Other Standards[S] |
| 상대 유전뮬, 1MHz |
2.7 / 4 |
- |
IEC 60250 |
| 소산 인자, 1MHz |
160 / 1000 |
E-4 |
IEC 60250 |
| 부피 저항 |
1E13 / 1E11 |
Ohm*m |
IEC 60093 |
| S: | These properties are reported by the producer according standards that are different to our defaults. |
| 기타 특성 | 건조/응축 | 단위 | 시험규격 |
| 물에서의 흡수성 |
8.1 / * |
% |
ISO 62와 유사 |
| 조건에서의 흡습성 |
2.6 / * |
% |
ISO 62와 유사 |
| 밀도 |
1100 / - |
kg/m³ |
ISO 1183 |
| 물질의 비성질 | 건조/응축 | 단위 | 시험규격 |
| ISO 데이터 |
| 점도수 |
125 / * |
cm³/g |
ISO 307, 1157, 1628 |
| Processing Recommendation Injection Molding | 값 | 단위 | 시험규격 |
| Pre-drying - Temperature |
<80 |
°C |
- |
| Pre-drying - Time |
4 - 6 |
h |
- |
| 용융수지온도 |
250 - 270 |
°C |
- |
| 성형온도 |
40 - 80 |
°C |
- |
특징
생산 공정
사출 성형
부가물
이형제
특별 특성
고충격 또는 고충격 보강, 열안정성
지역별 검색
짱쨌쨈
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.
