Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Promyde® B300 P2 G60 S - PA6-GF60 - Nurel S.A.

Material Data Center offers the following functions for Promyde® B300 P2 G60 S:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics건조/응축단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 35 / * cm³/10min ISO 1133
온도 275 / * °C -
하중 5 / * kg -
성형 수축률, 평행 0.2 / * % ISO 294-4, 2577
성형 수축률, 수직 0.3 / * % ISO 294-4, 2577
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 21000 / 17000 MPa ISO 527
인장 강도 240 / 190 MPa ISO 527
파단시 신율 2.5 / 2.1 % ISO 527
굴곡 계수, 23°C 19700 / 14400 MPa ISO 178
굴곡 강도 406 / 300 MPa ISO 178
챠피 충격 강도, +23°C 85 / 110 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 18 / 25 kJ/m² ISO 179/1eA
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 222 / * °C ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa 220 / * °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 220 / * °C ISO 75-1/-2
선형 열팽창 계수, 평행 13 / * E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 50 / * E-6/K ISO 11359-1/-2
1.5mm 평균두께에서의 난연성 HB / * class IEC 60695-11-10
테스트 두께 1.5 / * mm -
전기적 특성건조/응축단위시험규격
ISO 데이터
CTI 500 / - - IEC 60112
Other Standards[S]
부피 저항 1E13 / 1E11 Ohm*m IEC 60093
표면 저항 * / 1E10 Ohm IEC 60093
S: These properties are reported by the producer according standards that are different to our defaults.
기타 특성건조/응축단위시험규격
물에서의 흡수성 4.5 / * % ISO 62와 유사
조건에서의 흡습성 1.2 / * % ISO 62와 유사
밀도 1690 / - kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature <80 °C -
Pre-drying - Time 4 - 6 h -
용융수지온도 235 - 270 °C -
성형온도 40 - 80 °C -
특징
생산 공정
사출 성형
특별 특성
열안정성
응용
자동차의, 전기 및 전자
지역별 검색
짱쨌쨈
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.