Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Texin® 985A - TPU - Covestro Deutschland AG

Material Data Center offers the following functions for Texin® 985A:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Texin datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 기타 특성 - Processing Recommendation Injection Molding - Processing Recommendation Extrusion
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics값단위시험규격
ASTM 데이터
성형 수축률, 평행 0.008 mm/mm ASTM D 955
성형 수축률, 수직 0.008 mm/mm ASTM D 955
기계적 특성값단위시험규격
ASTM 데이터
굴곡 계수 26.9 MPa ASTM D 790
100% 변형시 탄성률 5.5 MPa ASTM D 412
300% 변형시 탄성률 3.2 MPa ASTM D 412
쇼어 A 경도 85 - ASTM D 2240
전단강도 87.6 kN/m ASTM D 624
압축세트, 22 hr @ 73 °F 19 % ASTM D 395
압축세트, 22 hr @ 158 °F 80 % ASTM D 395
인장 강도 38.6 MPa ASTM D 412
파단시 신율 590 % ASTM D 412
Other Standards[S]
Taber내마모성 30 mg/1000 cycles ASTM D 3489
S: These properties are reported by the producer according standards that are different to our defaults.
열적 특성값단위시험규격
ASTM 데이터
유리 전이 온도 -46 °C ASTM E 1356
비카트 연화 온도 80 °C ASTM D 1525
기타 특성값단위시험규격
밀도 1120 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 82 - 93 °C -
Pre-drying - Time 4 h -
Processing humidity ≤0.03 % -
용융수지온도 193 - 210 °C -
성형온도 16 - 43 °C -
Zone 1 182 - 202 °C -
Zone 2 185 - 204 °C -
Zone 3 185 - 204 °C -
Nozzle temperature 188 - 207 °C -
Screw speed 40 - 80 rpm -
Injection pressure 55.2 - 103 MPa -
Back pressure 5.52 MPa -
Processing Recommendation Extrusion값단위시험규격
용융수지온도 190 - 205 °C -
Feed temperature 182 - 199 °C -
Zone 1 182 - 204 °C -
Zone 2 182 - 204 °C -
Nozzle temperature 188 - 210 °C -
특징
생산 공정
사출 성형, Pipe/Tube Extrusion, 외형 압출, 시트 압출, 중공 성형
인도 유형
자연 색상
내화학성에
Hydrolytically Stable
Certifications
Food contact, Food approval FDA 21 CFR, Drinking water contact NSF 61
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.