Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VECTRA® A230 - LCP-CF30 - Celanese

Check here, which other Vectra datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 도표

Any use of this information falls under the rules of our disclaimer.

제품 설명서

Exceptional stiffness. Electrically conductive. 30% carbon fiber reinforced. Chemical abbreviation according to ISO 1043-1 : LCP Inherently flame retardant UL-Listing V-0 at 0.43mm thickness per UL 94 flame testing. Relative-Temperature-Index (RTI) according to UL 746B: electrical 130°C, mechanical 130°C. UL = Underwriters Laboratories (USA)

Flammability at thickness h

V-0

-

Processing/Physical Characteristics	값	단위	시험규격
ISO 데이터
성형 수축률, 평행	0.1	%	ISO 294-4, 2577
성형 수축률, 수직	0.3	%	ISO 294-4, 2577

기계적 특성	값	단위	시험규격
ISO 데이터
인장탄성률	23500	MPa	ISO 527
파단시 강도	149	MPa	ISO 527
파단시 신율	1.1	%	ISO 527
챠피 충격 강도 , +23°C	13	kJ/m²	ISO 179/1eU
챠피 노치드 충격 강도, +23°C	7	kJ/m²	ISO 179/1eA

열적 특성	값	단위	시험규격
ISO 데이터
녹는점, 10°C/min	280	°C	ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa	233	°C	ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa	250	°C	ISO 75-1/-2
비카트 연화 온도, B	179	°C	ISO 306
선형 열팽창 계수, 평행	2	E-6/K	ISO 11359-1/-2
선형 열팽창 계수, 수직	6	E-6/K	ISO 11359-1/-2
두께 H인 제품의 난연성	V-0	class	IEC 60695-11-10

전기적 특성	값	단위	시험규격
ISO 데이터
부피 저항	1	Ohm*m	IEC 62631-3-1
표면 저항	10	Ohm	IEC 62631-3-2

기타 특성	값	단위	시험규격
조건에서의 흡습성	0.06	%	ISO 62와 유사
밀도	1500	kg/m³	ISO 1183

도표

특징

생산 공정

사출 성형

인도 유형

펠렛 (입자,알갱이)

특별 특성

증가된 전기전도성, 정전기 방지, 난연성, 가시광선 안정성

지역별 검색

쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧

기타 정보

사E성

Vectra resins are well known for their excellent thermal and hydrolytic stability. In order to ensure these properties are optimum, the resin should be dried correctly prior to processing. Vectra A-grades should be dried at 150 C for a minimum of 4 hours in a desiccant dryer.
A three-zone screw evenly divided into feed, compression, and metering zones is preferred. A higher percentage of feed flights may be needed for smaller machines: 1/2 feed, 1/4 compression, 1/4 metering.

Vectra LCPs are shear thinning, their melt viscosity decreases quickly as shear rate increases. For parts that are difficult to fill, the molder can increase the injection velocity to improve melt flow.  To prevent thermal decomposition, off-gassing, and pressure build-up in the barrel, melt temperatures should not exceed 330°C.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.