Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VESTAMID® DX9303 BK E70288 - PA612-I - Evonik Operations GmbH

Material Data Center offers the following functions for VESTAMID® DX9303 BK E70288:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Vestamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성
Any use of this information falls under the rules of our disclaimer.
제품 설명서
High-viscosity, plasticized, heat- and light-stabilized, impact-modified polyamide 612 compound for extrusion

VESTAMID® DX9303 BK E70288 is a PA 612 extrusion compound developed for the production of tubing systems with higher requirements for heat resistance.

The melting point of VESTAMID® DX9303 BK E70288 is about 35°C higher than PA 11 and PA 12 compounds, allows higher peak temperatures in use. Thereby this compound fulfills the increased demands resulting from higher temperatures in the engine compartment.

If it is intended to use VESTAMID® DX9303 BK E70288 for fuel lines, certain preconditions must be observed. The Technical Marketing assists you in finding the suitable VESTAMID® compound.
At temperatures above 100°C tubing of VESTAMID® DX9303 BK E70288 allow a higher pressure load than tubing made of PA 12 compounds with comparable flexibility.

The process temperatures should be in the range of 240-270°C.

The material absorbs only little moisture. Therefore dimensions and properties of parts are nearly unaffected through ambient conditions.


Pigmentation may affect values.

Inside the original and undamaged packaging, the product has a shelf life of at least 2 years when stored in dry rooms at temperatures not exceeding 30°C.

For information about processing of VESTAMID®, please follow the general commendations about “Processing of VESTAMID® compounds”. 

FOR FURTHER INFORMATION PLEASE CONTACT US AT EVONIK-HP@EVONIK.COM
OR VISIT OUR PRODUCT AT  WWW.VESTAMID.COM

Processing/Physical Characteristics건조/응축단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 11 / * cm³/10min ISO 1133
온도 275 / * °C -
하중 5 / * kg -
성형 수축률, 평행 2.7 / * % ISO 294-4, 2577
성형 수축률, 수직 0.9 / * % ISO 294-4, 2577
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 900 / 680 MPa ISO 527
항복강도 38 / - MPa ISO 527
항복변형률 30 / - % ISO 527
파단시 평균신율 >50 / - % ISO 527
챠피 충격 강도 , +23°C N / N kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C N / N kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 87 / 135 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 11 / 15 kJ/m² ISO 179/1eA
Type of failure C / C(P)[C(P)] - -
쇼어 D 경도 70 / * - ISO 7619-1
C(P): CAMPUS
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 211 / * °C ISO 11357-1/-3
유리 전이 온도, 10 °C/min 20 / * °C ISO 11357-1/-2
하중하에서의 변형온도, 1.80 MPa 60 / * °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 142 / * °C ISO 75-1/-2
비카트 연화 온도, B 159 / * °C ISO 306
선형 열팽창 계수, 평행 150 / * E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 120 / * E-6/K ISO 11359-1/-2
1.5mm 평균두께에서의 난연성 HB / * class IEC 60695-11-10
테스트 두께 1.6 / * mm -
전기적 특성건조/응축단위시험규격
ISO 데이터
상대 유전율, 100Hz 4.7 / - - IEC 62631-2-1
상대 유전뮬, 1MHz 2.7 / - - IEC 62631-2-1
소산 인자, 100Hz 1450 / - E-4 IEC 62631-2-1
소산 인자, 1MHz 400 / - E-4 IEC 62631-2-1
부피 저항 2E10 / 5.3E8 Ohm*m IEC 62631-3-1
전기 압력 39 / 34 kV/mm IEC 60243-1
CTI 600 / - - IEC 60112
기타 특성건조/응축단위시험규격
물에서의 흡수성 2.4 / * % ISO 62와 유사
조건에서의 흡습성 1 / * % ISO 62와 유사
밀도 1050 / - kg/m³ ISO 1183
특징
생산 공정
Pipe/Tube Extrusion, 기타 압출
인도 유형
펠렛 (입자,알갱이), 검정
부가물
가소제
특별 특성
고충격 또는 고충격 보강, 가시광선 안정성, 열안정성
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.