Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VESTAMID® LX9013 BK 9.7507 - PA12-I - Evonik Operations GmbH

Material Data Center offers the following functions for VESTAMID® LX9013 BK 9.7507:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Vestamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
제품 설명서

High-viscosity, plasticized compound for extrusion with an extraordinary long-term heat resistance

VESTAMID® LX9013 BK 9.7507 is a plasticized polyamide 12 compound with an especially high long-term resistance under thermal load.

The material absorbs only little moisture, thus leading to nearly unaffected dimensions and properties of the finished parts at changing ambient conditions. Extruded tubes are impact-resistant also at low temperatures.

VESTAMID® LX9013 BK 9.7507 is suited to produce flexible tubes that are permanently exposed to higher temperatures, e.g., in the engine compartment of motor vehicles. Especially when used as diesel fuel lines they show significant advantages compared with standard grades, obvious in storage tests with diesel fuel (see the figure).

The material corresponds to the extrusion compound PA12-HIPHL, grade1 acc. DIN 73378 and meets the requirements acc. DIN 74324 (black), ISO 7628 and SAE J844.

VESTAMID® LX9013 BK 9.7507 is supplied as pellets in moisture-proof packaging ready for processing.

Inside the original and undamaged packaging, the product has a shelf life of at least 2 years when stored in dry rooms at temperatures not exceeding 30°C.

For information about processing of VESTAMID®, please follow the general commendations about “Processing of VESTAMID® compounds”. 

FOR FURTHER INFORMATION PLEASE CONTACT US AT EVONIK-HP@EVONIK.COM
OR VISIT OUR PRODUCT AT  WWW.VESTAMID.COM

Processing/Physical Characteristics건조/응축단위시험규격
ISO 데이터
성형 수축률, 평행 0.4 / * % ISO 294-4, 2577
성형 수축률, 수직 1.5 / * % ISO 294-4, 2577
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 410 / 400 MPa ISO 527
챠피 충격 강도 , +23°C N / N kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C N / N kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 130 / 140 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 7 / 20 kJ/m² ISO 179/1eA
Type of failure C / C - -
쇼어 D 경도 65 / * - ISO 7619-1
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 172 / * °C ISO 11357-1/-3
유리 전이 온도, 10 °C/min 0 / * °C ISO 11357-1/-2
하중하에서의 변형온도, 1.80 MPa 55 / * °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 130 / * °C ISO 75-1/-2
비카트 연화 온도, B 130 / * °C ISO 306
선형 열팽창 계수, 평행 160 / * E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 160 / * E-6/K ISO 11359-1/-2
1.5mm 평균두께에서의 난연성 HB / * class IEC 60695-11-10
테스트 두께 1.6 / * mm -
전기적 특성건조/응축단위시험규격
ISO 데이터
상대 유전율, 100Hz 12 / 15.6 - IEC 62631-2-1
상대 유전뮬, 1MHz 3.4 / 3.6 - IEC 62631-2-1
소산 인자, 100Hz 5000 / 6650 E-4 IEC 62631-2-1
소산 인자, 1MHz 1000 / 1390 E-4 IEC 62631-2-1
부피 저항 1E8 / 5.1E7 Ohm*m IEC 62631-3-1
전기 압력 25 / 23 kV/mm IEC 60243-1
CTI 600 / - - IEC 60112
기타 특성건조/응축단위시험규격
물에서의 흡수성 1.5 / * % ISO 62와 유사
조건에서의 흡습성 0.6 / * % ISO 62와 유사
밀도 1020 / 1020 kg/m³ ISO 1183
특징
생산 공정
Pipe/Tube Extrusion, 외형 압출, 기타 압출
인도 유형
펠렛 (입자,알갱이), 검정
부가물
가소제
특별 특성
고충격 또는 고충격 보강, 열안정성
지역별 검색
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.