Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of Bakelite® PF 31.5 - PF-X - Bakelite Synthetics
Material Data Center offers the following functions for Bakelite® PF 31.5:
unit conversion, PDF datasheet print, comparison with other plastics
Check here, which other Bakelite datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our
disclaimer.
제품 설명서
Product description:
Phenolic moulding compound, mainly organically filled, electrically high grade.
Application areas:
Parts for electrical and telecommunications technology, car electronics, terminal boards and baseplates, housings, mounting parts, motor ignition systems.
| Property Name |
Value |
Unit |
Standard No. |
|---|
| Apparent density (moulding compound) |
0.6 |
g/cm³ |
ISO 60 |
| Moulding shrinkage (injection moulding, longitudinal) |
0.9 |
% |
ISO 2577 |
| Post shrinkage (injection moulding, 168h/110°C) |
0.95 |
% |
ISO 2577 |
| Moulding shrinkage (compression moulding, longitudinal) |
0.45 |
% |
ISO 2577 |
| Post shrinkage (compression moulding, 168h/110°C) |
0.45 |
% |
ISO 2577 |
| Flexural strength (2mm/min) |
110 |
MPa |
ISO 178 |
| Flexural modulus |
8000 |
MPa |
ISO 178 |
| Ball indentation hardness (H 961/30) |
300 |
MPa |
ISO 2039/P1 |
| Water absorption (24h/23°C) |
37 |
mg |
similar to ISO 62 |
Preparation of Test Specimens of Thermosetting Moulding Compound- Compression to ISO 295
- Injection to ISO 10724
Storage capability
6 months (relative humidity of 50-60% and maximum storage temperature of approximately 20°C)
| Processing/Physical Characteristics | 값 | 단위 | 시험규격 |
| ISO 데이터 |
| 성형 수축률, 평행 |
0.9 |
% |
ISO 294-4, 2577 |
| 기계적 특성 | 값 | 단위 | 시험규격 |
| ISO 데이터 |
| 챠피 충격 강도 , +23°C |
8 |
kJ/m² |
ISO 179/1eU |
| 챠피 노치드 충격 강도, +23°C |
1.8 |
kJ/m² |
ISO 179/1eA |
| 열적 특성 | 값 | 단위 | 시험규격 |
| ISO 데이터 |
| 하중하에서의 변형온도, 8.00 MPa |
115 |
°C |
ISO 75-1/-2 |
| 전기적 특성 | 값 | 단위 | 시험규격 |
| ISO 데이터 |
| 상대 유전율, 100Hz |
7 |
- |
IEC 62631-2-1 |
| 소산 인자, 100Hz |
0.13 |
E-4 |
IEC 62631-2-1 |
| 부피 저항 |
1E10 |
Ohm*m |
IEC 62631-3-1 |
| 표면 저항 |
1E11 |
Ohm |
IEC 62631-3-2 |
| 전기 압력 |
28 |
kV/mm |
IEC 60243-1 |
| CTI |
125 |
- |
IEC 60112 |
| 기타 특성 | 값 | 단위 | 시험규격 |
| 밀도 |
1440 |
kg/m³ |
ISO 1183 |
| 테스트 견본 생산 | 값 | 단위 | 시험규격 |
| ISO 데이터 |
| 사출성형: 사출온도 |
115 |
°C |
ISO 10724 |
| 사출성형: 사출속도 |
170 |
mm/s |
ISO 10724 |
| 사출성형: 보압 |
100 |
MPa |
ISO 10724 |
| 사출성형: 경화시간 |
25 |
min |
ISO 10724 |
| 압축성형: 성형온도 |
160 |
°C |
ISO 295 |
| 압축성형: 경화시간 |
1 |
min |
ISO 295 |
특징
생산 공정
사출 성형, 트랜스퍼 성형
지역별 검색
기타 정보
사E성
VERARBEITUNG
| Temperature of material: |
80 - 100 |
°C |
| Mould temperature: |
160 - 190 |
°C |
| Curing time: |
10-20 |
sec |
| |
| Further Information: |
| Barrel temperature |
| - Feed zone: |
60-75 |
°C |
| - Nozzle zone: |
80-100 |
°C |
| Cavity moulding pressure: |
>15 |
MPa |
| Back pressure: |
0.5-2 |
MPa |
| Holding pressure: |
60% of injection pressure |
압E성
PROCESSING
| Mould temperature: | 160-190 | °C |
| Curing time: | 20-40 | sec |
| Cavity moulding pressure: | >15 | MPa |
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.
