Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Durabio™ D7340 - PC - Mitsubishi Chemical Performance Polymers

Material Data Center offers the following functions for Durabio™ D7340:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Durabio datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 광학 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 8 cm³/10min ISO 1133
온도 230 °C -
하중 2.16 kg -
용융 흐름성, MFI 10 g/10min ISO 1133
온도 230 °C -
负荷 2.16 kg -
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 2700 MPa ISO 527
인장 강도 79 MPa ISO 527
파단시 신율 72 % ISO 527
굴곡 계수, 23°C 2700 MPa ISO 178
굴곡 강도 116 MPa ISO 178
챠피 충격 강도, +23°C N kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 7 kJ/m² ISO 179/1eA
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 102 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 114 °C ISO 75-1/-2
선형 열팽창 계수, 평행 69 E-6/K ISO 11359-1/-2
선형 열팽창 계수, 수직 69 E-6/K ISO 11359-1/-2
광학 특성값단위시험규격
ISO Data
광선 투겠淅 92 % ISO 13468-1, -2
기타 특성값단위시험규격
밀도 1360 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 90 - 100 °C -
Pre-drying - Time 5 - 7 h -
용융수지온도 230 - 250 °C -
성형온도 60 - 80 °C -
Feed temperature 220 - 260 °C -
Zone 1 220 - 260 °C -
Nozzle temperature 220 - 260 °C -
Screw speed 50 rpm -
Injection pressure 50 - 95 MPa -
Back pressure 10 MPa -
특징
생산 공정
사출 성형
인도 유형
검정
특별 특성
열안정성, 투명도
특성
Light Guiding
Certifications
Contains renewable resources
응용
자동차의, 전기 및 전자 , 포장, 스포츠 장비
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.