Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of MABLEX® 274 - (PC+ABS) - Ravago Group

Material Data Center offers the following functions for MABLEX® 274:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Mablex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 흐름성, MFI 13 g/10min ISO 1133
온도 260 °C -
负荷 5 kg -
성형 수축률, 평행 0.6 % ISO 294-4, 2577
기계적 특성값단위시험규격
ISO 데이터
항복강도 58 MPa ISO 527
파단시 강도 48 MPa ISO 527
파단시 신율 52 % ISO 527
굴곡 계수, 23°C 2400 MPa ISO 178
아이조드 충격은 노치, +23°C 55 kJ/m² ISO 180/1A
아이조드 충격은 노치 30 kJ/m² ISO 180/1A
온도 -30 °C -
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 110 °C ISO 75-1/-2
비카트 연화 온도, A 132 °C ISO 306
비카트 연화 온도, B 124 °C ISO 306
1.5mm 평균두께에서의 난연성 HB class IEC 60695-11-10
테스트 두께 1.6 mm -
두께 H인 제품의 난연성 HB class IEC 60695-11-10
테스트 두께 3.2 mm -
연소속도, FMVSS, 두께 1mm 48 mm/min ISO 3795 (FMVSS 302)
Glow Wire Flammability Index (GWFI) 650 °C IEC 60695-2-12
GWFI - thickness tested (1) 2 mm -
전기적 특성값단위시험규격
ISO 데이터
부피 저항 1E13 Ohm*m IEC 62631-3-1
표면 저항 1E14 Ohm IEC 62631-3-2
전기 압력 24 kV/mm IEC 60243-1
CTI 300 - IEC 60112
기타 특성값단위시험규격
밀도 1130 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 100 °C -
Pre-drying - Time 3 - 4 h -
Processing humidity ≤0.05 % -
용융수지온도 250 - 270 °C -
성형온도 50 - 80 °C -
Zone 1 225 - 240 °C -
Zone 2 240 - 260 °C -
Zone 3 260 - 270 °C -
Nozzle temperature 250 - 260 °C -
Screw speed 40 - 70 rpm -
Back pressure 0.3 - 1.5 MPa -
유지압력 3 - 7 MPa -
특징
생산 공정
사출 성형
특별 특성
열안정성
지역별 검색
짱쨌쨈
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.