Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of POLYFORT® FIPP 20 T - PP-T20 - LyondellBasell Industries

Material Data Center offers the following functions for POLYFORT® FIPP 20 T:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Polyfort datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
20% talc filled PP copolymer compound

Processing/Physical Characteristics값단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 7 cm³/10min ISO 1133
온도 230 °C -
하중 2.16 kg -
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 2200 MPa ISO 527
항복강도 25 MPa ISO 527
항복변형률 4 % ISO 527
챠피 충격 강도 , +23°C N kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C 36 kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 6.5 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 4 kJ/m² ISO 179/1eA
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 64 °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 103 °C ISO 75-1/-2
비카트 연화 온도, B 70 °C ISO 306
1.5mm 평균두께에서의 난연성 HB class IEC 60695-11-10
테스트 두께 1.5 mm -
Yellow Card 유효한 예 - -
두께 H인 제품의 난연성 HB class IEC 60695-11-10
테스트 두께 3.0 mm -
Yellow Card 유효한 예 - -
연소속도, FMVSS, 두께 1mm 100 mm/min ISO 3795 (FMVSS 302)
전기적 특성값단위시험규격
ISO 데이터
부피 저항 >1E13 Ohm*m IEC 62631-3-1
표면 저항 >1E15 Ohm IEC 62631-3-2
기타 특성값단위시험규격
밀도 1050 kg/m³ ISO 1183
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 80 °C -
Pre-drying - Time 2 - 4 h -
용융수지온도 230 - 270 °C -
성형온도 40 - 70 °C -
특징
생산 공정
사출 성형
인도 유형
과립
부가물
이형제
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
기타 정보
사E성
PREPROCESSING; Pretreatment
Predrying usually not neccessary (2-4h / 80°C)

PROCESSING ;Processing:

Melttemperature230 - 270°C
Mouldtemperature40 - 70°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.