Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Promyde® BF40 L - PA6 - Nurel S.A.

Material Data Center offers the following functions for Promyde® BF40 L:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
열적 특성 - 광학 특성 - 기타 특성 - 기계적 성질 (필름) - Processing Recommendation Extrusion
Any use of this information falls under the rules of our disclaimer.
열적 특성값단위시험규격
ISO 데이터
녹는점, 10°C/min 220 °C ISO 11357-1/-3
광학 특성값단위시험규격
ASTM 데이터
탁도 5[1] % ASTM D 1003
1: Chill roll temperature 90ºC
기타 특성값단위시험규격
물에서의 흡수성 9 % ISO 62와 유사
조건에서의 흡습성 3 % ISO 62와 유사
밀도 1130 kg/m³ ISO 1183
Moisture Content 0.1 % -
기계적 성질 (필름) 값단위시험규격
ISO 데이터
항복시의 강도, 평행 34 MPa ISO 527-3
파단시 강도, 평행 96 MPa ISO 527-3
최대변형율, 평행 350 % ISO 527-3
트라우저 전단강도, 평행 25 N/mm ISO 6383-1
동적마찰계수 0.25 - ISO 8295
수증기 투과속도, 23°C/85%RH 15 g/(m²*d) ISO 15106-1/-2
산소 투과율, 23°C/0%r.h. 25 cm³/(m²*d*bar) ISO 15105-1/-2
산소 투과율, 23°C/85%RH 40 cm³/(m²*d*bar) ISO 15105-1/-2
Processing Recommendation Extrusion값단위시험규격
Pre-drying - Temperature 75 - 80 °C -
Feed temperature 230 - 240 °C -
Zone 1 250 - 265 °C -
Zone 2 255 - 265 °C -
Nozzle temperature 255 - 265 °C -
특징
생산 공정
Blown Film Extrusion, 필름 압출, 기타 압출, 열성형
부가물
윤활제
특성
Barrier Properties
내화학성에
General Chemical Resistance
Certifications
Food contact
응용
포장
지역별 검색
짱쨌쨈
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.