Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Rilsamid® AMN BLACK P20 TLD - PA12 - ARKEMA

Material Data Center offers the following functions for Rilsamid® AMN BLACK P20 TLD:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Rilsamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 기타 특성
Any use of this information falls under the rules of our disclaimer.
제품 설명서
PA12-P, MHLR, 12-005
Rilsamid® AMN BLACK P20 TLD resin is a black colored polyamide. This grade is plasticized and designed for injection molding.
Processing/Physical Characteristics건조/응축단위시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR 44 / * cm³/10min ISO 1133
온도 235 / * °C -
하중 2.16 / * kg -
성형 수축률, 평행 1.9 / * % ISO 294-4, 2577
성형 수축률, 수직 1.9 / * % ISO 294-4, 2577
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 - / 550 MPa ISO 527
항복강도 - / 31 MPa ISO 527
항복변형률 - / 19 % ISO 527
파단시 평균신율 - / >50 % ISO 527
챠피 노치드 충격 강도, +23°C - / 18 kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C - / 4 kJ/m² ISO 179/1eA
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 174 / * °C ISO 11357-1/-3
기타 특성건조/응축단위시험규격
밀도 1020 / 1020 kg/m³ ISO 1183
특징
생산 공정
사출 성형
인도 유형
펠렛 (입자,알갱이), 검정
부가물
이형제, 가소제
특별 특성
가시광선 안정성, U.V. 안정성 또는 기후 안정성, 열안정성
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
기타 정보
사E성

Processing conditions, Injection:

- Typical melt temperature (Min / Recommended / Max) : 250°C / 270°C / 290°C.
- Mold temperature : 20 - 40°C
- Drying time and temperature (only necessary for bags opened for more than two hours) : 4-6 hours at 80 - 90°C.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.