Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox. Information about Biopolymers, a project by FH Hannover and M-Base Engineering & Software GmbH sponsored by Fachagentur Nachwachsende Rohstoffe (FNR).

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Inzea® F29 HT 30 - (PLA+PSAC) - Nurel S.A.

Material Data Center offers the following functions for Inzea® F29 HT 30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Inzea datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 4700 MPa ISO 527
Resistência à tração 48 MPa ISO 527
Deformação no escoamento 3 % ISO 527
Deformação na ruptura 5 % ISO 527
Módulo de flexão, 23°C 5000 MPa ISO 178
Res. impacto Charpy c/entalhe, +23°C 6.5 kJ/m² ISO 179/1eA
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 177 °C ISO 11357-1/-3
Temperatura de deflexão térmica , 0.45 MPa 62 °C ISO 75-1/-2
Outras propriedadesValorUnidadeMétodo de ensaio
Biobased content 80 % -
Moisture Content 1 % -
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 50 °C -
Temperatura da massa 200 - 210 °C -
Temperatura do molde 100 - 120 °C -
Características
Processamento
Moldagem por injeção, Moldagem por sopro
Características especiais
Estável contra o calor
Certifications
Contém recursos renováveis, Biodegradável, Contacto com alimentos, Aprovação para contacto com alimentos10/2011, Compostable ISO 13432 (Produtor), Compostable ISO 13432 (Certificado)
Disponibilidade regional
Europa, America Centra e do Sul
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.