Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LOXISTER PBT FRV0 GF30 02030 - PBT-GF30 - Loxim Industries Limited

Material Data Center offers the following functions for LOXISTER PBT FRV0 GF30 02030:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Loxister datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Tensão na ruptura 100 MPa ISO 527
Deformação na ruptura 4 % ISO 527
Módulo de flexão, 23°C 9700 MPa ISO 178
Resistência à flexão 165 MPa ISO 178
Impacto Izod com entalhe, +23°C 7 kJ/m² ISO 180/1A
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica, 1.80 MPa 200 °C ISO 75-1/-2
Temperatura de deflexão térmica , 0.45 MPa 215 °C ISO 75-1/-2
Flamabilidade a 1.5mm esp. nom. V-0 class IEC 60695-11-10
Espessuras do tubo de teste 1.6 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 1 mm -
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1650 kg/m³ ISO 1183
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 100 - 120 °C -
Pré-secagem - tempo 4 h -
Umidade do processamento ≤0.04 % -
Temperatura da massa 250 - 270 °C -
Temperatura do molde 60 - 100 °C -
Características
Processamento
Moldagem por injeção
Características especiais
Retardante de chama, Estável contra o calor
Resistência Química
Resistência química geral
Aplicaciones
Automóvel, Elétrica e Eletrônica
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.