Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Moplen EP5015 - PP - PolyMirae

Material Data Center offers the following functions for Moplen EP5015:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Moplen datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez, MFI 15 g/10min ISO 1133
Temperatura 230 °C -
ASTM Dados
Índice de fluidez, MFI 15 g/10min ASTM D 1238
Temperatura 230 °C -
Carga 2.16 kg -
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Tensão no escoamento 20 MPa ISO 527
Deformação no escoamento 6 % ISO 527
Módulo de flexão, 23°C 1100 MPa ISO 178
Resistência ao impacto Charpy, +23°C N kJ/m² ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C 15 kJ/m² ISO 179/1eA
ASTM Dados
Resistência à tração no escoamento 22.6 MPa ASTM D 638
Alongamento no escoamento 8 % ASTM D 638
Módulo de flexão 1079 MPa ASTM D 790
Impacto Izod com entalhe, 1/8 in N J/m ASTM D 256
Impacto Izod com entalhe, baixa temperatura 94.2 J/m ASTM D 256
Temperatura -20 °C -
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica , 0.45 MPa 70 °C ISO 75-1/-2
ASTM Dados
DTUL @ 66 psi 90 °C ASTM D 648
Temperatura de amolecimento Vicat 130 °C ASTM D 1525
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 900 kg/m³ ISO 1183
Densidade 900 kg/m³ ASTM D 792
Características
Processamento
Moldagem por injeção
Características especiais
Alto impacto.
Características
Blush Resistance/Low Crease Whitening, Baixa deformação, Nucleado, Copolímero
Certifications
Contacto com alimentos, Aprovação de alimentos FDA 21 CFR
Aplicaciones
Equipo deportivo
Disponibilidade regional
Ásia Pacífico, Oriente/África
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.