Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NYLENE 406F - PA6 - Polymeric Resources Corporation

Material Data Center offers the following functions for NYLENE 406F:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Nylene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ASTM Dados
Resistência à tração 75.2 MPa ASTM D 638
Módulo de flexão 2758 MPa ASTM D 790
Impacto Izod com entalhe, 1/8 in 42.7 J/m ASTM D 256
Propriedades térmicasValorUnidadeMétodo de ensaio
ASTM Dados
DTUL @ 66 psi 182 °C ASTM D 648
DTUL @ 264 psi 71.1 °C ASTM D 648
Temperatura de fusão 216 °C ASTM D 3418
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1130 kg/m³ ASTM D 792
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 66 - 82 °C -
Pré-secagem - tempo 2 - 4 h -
Umidade do processamento ≤0.2 % -
Temperatura da massa 238 - 271 °C -
Temperatura do molde 49 - 93 °C -
Zona 1 221 - 249 °C -
Zona 2 227 - 260 °C -
Zona 3 238 - 271 °C -
Temperatura do bico 238 - 271 °C -
Pressão de injeção 4 - 12 MPa -
Contrapressão 0 - 50 MPa -
Pressão de recalque 3 - 9 MPa -
Tempo de residência máximo 6 min -
Características
Processamento
Moldagem por injeção
Certifications
Contacto com alimentos, Aprovação de alimentos FDA 21 CFR, Aprovação de alimentos NSF 51
Aplicaciones
Polivalente, Embalaje
Disponibilidade regional
América do Norte
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.