Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Pebax® 2533 SA 01 - TPA - ARKEMA

Check here, which other Pebax datasheets, application examples or technical articles are available in Material Data Center

Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Diagrama

Any use of this information falls under the rules of our disclaimer.

Informação do produto

Polyether block amide Pebax® 2533 SA 01 resin is a thermoplastic elastomer made of flexible polyether and rigid polyamide.
This SA grade is specially designed to food uses. Its chemical structure also enables the absorption and the controlled release of volatile molecules (fragrances, oils, insecticides...).


Main applications:

• Flexible injected parts
• Controlled release of volatile molecules (fragrances
• oils
• insecticides
• etc...)
• Note: this grade is not recommended by Arkema for usage in medical applications. For such applications Pebax® SA 01 MED should be used

Packaging:
This grade is delivered dried in sealed packaging (25 kg bags or 550kg rigid containers) ready to be processed.

Shelf Life:
Two years from the delivery. For any use above this limit, please refer to our technical services.

Propriedades mecânicas	Seco / Cond	Unidade	Método de ensaio
ISO Dados
Módulo de tração	12 / 10	MPa	ISO 527
Tensão a 50% de deformação	3 / 3	MPa	ISO 527
Deformação na ruptura	>50 / >50	%	ISO 527
Tensão em 10% de alongamento	1 / *	MPa	ISO 527
Tensão em 100% de alongamento	4 / *	MPa	ISO 527
Tensão em 300% de alongamento	5 / *	MPa	ISO 527
Tensão na Ruptura TPE	32 / *	MPa	ISO 527
Deformação na Ruptura TPE	>300 / *	%	ISO 527
Dureza Shore A	74 / *	-	ISO 7619-1
Dureza Shore D	22 / *	-	ISO 7619-1

Propriedades térmicas	Seco / Cond	Unidade	Método de ensaio
ISO Dados
Temperatura de fusão, 10°C/min	134 / *	°C	ISO 11357-1/-3

Outras propriedades	Seco / Cond	Unidade	Método de ensaio
Absorção de água	1.2 / *	%	Sim. to ISO 62
Absorção de umidade	0.4 / *	%	Sim. to ISO 62
Densidade	1000 / 1000	kg/m³	ISO 1183

Diagrama

Características

Processamento

Moldagem por injeção

Forma de entrega

Granulos

Aditivos

Lubrificantes

Características especiais

Estável a luz, Estável contra o calor

Certifications

Contacto com alimentos

Disponibilidade regional

América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África

Outras informações

Moldagem por injeção

Processing conditions:

- Typical melt temperature (Min / Recommended / Max) : 180°C / 210°C / 240°C.
- Typical mold temperature : 10 – 30°C.
- Drying time and temperature (only necessary for bags/containers opened for more than two hours) : 4-8 hours at 55-65°C.  

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.