Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Velocity® LGF60 - PA6 - PA6-GF60 - PlastiComp, Inc.

Material Data Center offers the following functions for Velocity® LGF60 - PA6:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Velocity datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Informação do produto
For more detailed information, please read our
or contact our representatives in your region.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ASTM Dados
Módulo de tração 19990 MPa ASTM D 638
Resistência à tração 255 MPa ASTM D 638
Alongamento no escoamento 1.5 % ASTM D 638
Módulo de flexão 17240 MPa ASTM D 790
Resistência à flexão 407 MPa ASTM D 790
Impacto Izod com entalhe, 1/8 in 320 J/m ASTM D 256
Resistência ao Impacto Izod, 1/8 in 1280 J/m ASTM D 256
Propriedades térmicasValorUnidadeMétodo de ensaio
ASTM Dados
DTUL @ 264 psi 221 °C ASTM D 648
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1690 kg/m³ ASTM D 792
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 85 °C -
Pré-secagem - tempo 4 h -
Umidade do processamento ≤0.18 % -
Temperatura da massa 271 - 288 °C -
Temperatura do molde 93 °C -
Zona 1 260 - 277 °C -
Zona 2 266 - 282 °C -
Zona 3 271 - 288 °C -
Temperatura do bico 271 - 288 °C -
Velocidade de parafuso 30 - 50 rpm -
Velocidade de injeção 51 - 76 mm/s -
Contrapressão 0.17 - 0.35 MPa -
Características
Processamento
Moldagem por injeção
Características
Long fiber reinforced
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.