Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Versalloy™ HC 9210-45N - TPV - Avient Corporation

Material Data Center offers the following functions for Versalloy™ HC 9210-45N:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Versalloy datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ASTM Dados
Módulo a 100% alongamento 1.1 MPa ASTM D 412
Módulo a 300% alongamento 0.74 MPa ASTM D 412
Dureza Shore A 45 - ASTM D 2240
Resistência ao rasgamento 17.5 kN/m ASTM D 624
Resistência à compressão, 22 hr @ 73 °F 19 % ASTM D 395
Resistência à compressão, 22 hr @ 158 °F 34 % ASTM D 395
Resistência à tração na ruptura 3.34 MPa ASTM D 412
Deformação na ruptura 480 % ASTM D 412
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 890 kg/m³ ASTM D 792
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Temperatura do molde 15.6 - 26.7 °C -
Zona 1 149 - 188 °C -
Zona 2 160 - 199 °C -
Zona 3 171 - 210 °C -
Temperatura do bico 171 - 210 °C -
Velocidade de parafuso 50 - 100 rpm -
Velocidade de injeção 25.4 - 127 mm/s -
Contrapressão 0.689 - 1.38 MPa -
Pressão de recalque 1.45 - 3.38 MPa -
Características
Processamento
Moldagem por injeção
Forma de entrega
Granulos, Cor natural
Características especiais
Sem halogéneo
Características
Boa adesão, Soft Feel
Certifications
USP Class VI
Aplicaciones
Médico
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.