Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of XEBRID 1-C20-G30 - PA66-(CF+GF)50 - Xenia Srl

Material Data Center offers the following functions for XEBRID 1-C20-G30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Xebrid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Contração após a moldagem, paralelo 0.2 % ISO 294-4, 2577
Contração após a moldagem, perpendicular 0.3 % ISO 294-4, 2577
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 25000 MPa ISO 527
Tensão na ruptura 245 MPa ISO 527
Deformação na ruptura 2.1 % ISO 527
Módulo de flexão, 23°C 18500 MPa ISO 178
Resistência à flexão 340 MPa ISO 178
Resistência ao Impacto Izod, +23°C 60 kJ/m² ISO 180/1U
Impacto Izod com entalhe, +23°C 12 kJ/m² ISO 180/1A
Impacto Izod com entalhe 9 kJ/m² ISO 180/1A
Temperatura -30 °C -
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica , 8.00 MPa 210 °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 250 °C ISO 306
Propriedades elétricasValorUnidadeMétodo de ensaio
ISO Dados
Resistividade volumétrica específica 0.05 Ohm*m IEC 62631-3-1
Resistividade superficial específica 100 Ohm IEC 62631-3-2
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1480 kg/m³ ISO 1183
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 80 - 100 °C -
Pré-secagem - tempo 6 - 8 h -
Temperatura da massa 265 - 280 °C -
Temperatura do molde 110 °C -
Características
Processamento
Moldagem por injeção
Disponibilidade regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.