Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ECONAMID FL 66/6G15 - PA666-GF15 - DOMO Engineering Plastics

Material Data Center offers the following functions for ECONAMID FL 66/6G15:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Econamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Propriedades térmicas - Propriedades elétricas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 4700 MPa ISO 527
Tensão na ruptura 110 MPa ISO 527
Deformação na ruptura 2.5 % ISO 527
Res. impacto Charpy c/entalhe, +23°C 6 kJ/m² ISO 179/1eA
Impacto Izod com entalhe, +23°C 5 kJ/m² ISO 180/1A
Dureza Rockwell R 120 - ISO 2039-2
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 262 °C ISO 11357-1/-3
Temperatura de deflexão térmica, 1.80 MPa 215 °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 220 °C ISO 306
Flamabilidade a espessura h HB class IEC 60695-11-10
Espessuras do tubo de teste 0.8 mm -
Propriedades elétricasValorUnidadeMétodo de ensaio
ISO Dados
Resistividade volumétrica específica 1E13 Ohm*m IEC 62631-3-1
Resistividade superficial específica 1E13 Ohm IEC 62631-3-2
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1260 kg/m³ ISO 1183
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 75 - 85 °C -
Pré-secagem - tempo 2 - 4 h -
Temperatura da massa 260 - 290 °C -
Temperatura do molde 90 °C -
Características
Processamento
Moldagem por injeção
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.