Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ferrex GPP20CF57HB-GY - PP-K21 - LyondellBasell Industries

Material Data Center offers the following functions for Ferrex GPP20CF57HB-GY:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Ferrex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ASTM Dados
Índice de fluidez, MFI 25 g/10min ASTM D 1238
Temperatura 230 °C -
Carga 2.16 kg -
Propriedades mecânicasValorUnidadeMétodo de ensaio
ASTM Dados
Resistência à tração no escoamento 30.3 MPa ASTM D 638
Deformação na ruptura 44 % ASTM D 638
Módulo de flexão 1793 MPa ASTM D 790
Dureza Shore D 73 - ASTM D 2240
Impacto Gardner 13.6 J ASTM D 2794,4226,5420
Impacto Izod com entalhe, 1/8 in 32.6 J/m ASTM D 256
Resistência ao Impacto Izod, 1/8 in 854 J/m ASTM D 256
Propriedades térmicasValorUnidadeMétodo de ensaio
ASTM Dados
UL94 flamabilidade HB - UL 94
DTUL @ 66 psi 107 °C ASTM D 648
DTUL @ 264 psi 60.6 °C ASTM D 648
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1060 kg/m³ ASTM D 792
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 93.3 °C -
Pré-secagem - tempo 2 - 3 h -
Temperatura do molde 46.1 - 60 °C -
Zona 1 199 - 204 °C -
Zona 2 204 - 210 °C -
Zona 3 210 - 216 °C -
Temperatura do bico 216 - 221 °C -
Velocidade de parafuso 100 - 150 rpm -
Contrapressão 0.138 - 0.345 MPa -
Características
Processamento
Moldagem por injeção
Forma de entrega
Granulos
Características
High Gloss, Homopolímero
Disponibilidade regional
América do Norte, America Centra e do Sul
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.