Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Makrolon® 6487 R30 CQ - PC - Covestro Deutschland AG

Material Data Center offers the following functions for Makrolon® 6487 R30 CQ:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Makrolon datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 11 cm³/10min ISO 1133
Temperatura 300 °C -
Carga 1.2 kg -
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 2350 MPa ISO 527
Tensão no escoamento 67 MPa ISO 527
Deformação no escoamento 6 % ISO 527
Deformação nominal na ruptura >50 % ISO 527
Tensão na ruptura 67 MPa ISO 527
Deformação na ruptura 110 % ISO 527
Resistência ao impacto Charpy, -30°C N kJ/m² ISO 179/1eU
Impacto Izod com entalhe, +23°C 15[1] kJ/m² ISO 180/1A
Perfuração - força máxima, +23°C 5200 N ISO 6603-2
Perfuração - força máxima, -30°C 6100 N ISO 6603-2
Energia de perfuração, +23°C 50 J ISO 6603-2
Energia de perfuração, -30°C 50 J ISO 6603-2
1: 3 mm
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica, 1.80 MPa 122 °C ISO 75-1/-2
Temperatura de deflexão térmica , 0.45 MPa 136 °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 141 °C ISO 306
Flamabilidade a 1.5mm esp. nom. V-0 class IEC 60695-11-10
Espessuras do tubo de teste 1.5 mm -
Cartão Amarelo (yellow card) disponível sim - -
Flamabilidade a espessura h V-0 class IEC 60695-11-10
Espessuras do tubo de teste 3.0 mm -
Cartão Amarelo (yellow card) disponível sim - -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 1 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (2) 3 mm -
Other Standards[S]
Flamabilidade 5V a espessura h 5VA class Producer Method
Espessuras do tubo de teste 3.0 mm -
S: These properties are reported by the producer according standards that are different to our defaults.
Propriedades elétricasValorUnidadeMétodo de ensaio
ISO Dados
Constante dielétrica, 100Hz 3 - IEC 62631-2-1
Constante dielétrica, 1MHz 3 - IEC 62631-2-1
Fator de dissipação dielétrica, 100Hz 7 E-4 IEC 62631-2-1
Fator de dissipação dielétrica, 1MHz 96 E-4 IEC 62631-2-1
Resistividade volumétrica específica 9E16 Ohm*m IEC 62631-3-1
Resistividade superficial específica 2E16 Ohm IEC 62631-3-2
Índice comparativo de linha de fuga 225 - IEC 60112
Outras propriedadesValorUnidadeMétodo de ensaio
Recycled resin content 30 % -
Produção de amostra para testeValorUnidadeMétodo de ensaio
ISO Dados
Moldagem por injeção, temperatura da massa 300 °C ISO 294
Moldagem por injeção, temperatura do molde 80 °C ISO 294
Moldagem por injeção, velocidade de injeção 200 mm/s ISO 294
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 120 °C -
Pré-secagem - tempo 2 - 3 h -
Umidade do processamento ≤0.02 % -
Temperatura da massa 280 - 320 °C -
Temperatura do molde 80 - 120 °C -
Zona 1 250 - 260 °C -
Zona 2 270 - 280 °C -
Zona 3 280 - 290 °C -
Temperatura do bico 290 - 300 °C -
Contrapressão 5 - 15 MPa -
Características
Processamento
Moldagem por injeção
Forma de entrega
Negro
Aditivos
Desmoldante
Características especiais
Retardante de chama, Estabilidade a raios U.V./Intempéries, Opaque
Certifications
Conteúdo de resina reciclada, Post-Consumer Recyclate
Aplicaciones
Elétrica e Eletrônica
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.