Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Starflam M10009A - PP - Eurostar Engineering Plastics

Material Data Center offers the following functions for Starflam M10009A:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Starflam datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 10 cm³/10min ISO 1133
Temperatura 230 °C -
Carga 5 kg -
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Tensão no escoamento 38 MPa ISO 527
Deformação no escoamento 7.3 % ISO 527
Tensão na ruptura 25 MPa ISO 527
Módulo de flexão, 23°C 1900 MPa ISO 178
Resistência ao Impacto Izod, +23°C 45 kJ/m² ISO 180/1U
Impacto Izod com entalhe, +23°C 4 kJ/m² ISO 180/1A
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica, 1.80 MPa 57 °C ISO 75-1/-2
Temperatura de deflexão térmica , 0.45 MPa 103 °C ISO 75-1/-2
Coef. de expansão térmica linear, paralelo 106 E-6/K ISO 11359-1/-2
Coef. de expansão térmica linear, perpend. 140 E-6/K ISO 11359-1/-2
ASTM Dados
UL94 flamabilidade V-2 - UL 94
Espessuras do tubo de teste 1.6 mm -
Outras propriedadesValorUnidadeMétodo de ensaio
Absorção de água 0.01 % Sim. to ISO 62
Densidade 1000 kg/m³ ISO 1183
Características
Processamento
Moldagem por injeção
Características especiais
Retardante de chama
Características
Homopolímero
Disponibilidade regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.