Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of TECACOMP® PEEK 450 CMF white 3809 - PEEK-Z - Ensinger Compounds

Material Data Center offers the following functions for TECACOMP® PEEK 450 CMF white 3809:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Tecacomp datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Propriedades térmicas - Propriedades elétricas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 5000 MPa ISO 527
Resistência à tração 100 MPa ISO 527
Deformação na ruptura 9 % ISO 527
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 343 °C ISO 11357-1/-3
Temp. de transição vítrea, 10 °C/min 143 °C ISO 11357-1/-2
Propriedades elétricasValorUnidadeMétodo de ensaio
ISO Dados
Resistência elétrica 15.8 kV/mm IEC 60243-1
Other Standards[S]
Resistividade volumétrica específica 2.71E13 Ohm*m ISO 3915
Resistividade superficial específica 3.53E15 Ohm ISO 3915
S: These properties are reported by the producer according standards that are different to our defaults.
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1630 kg/m³ ISO 1183
Bulk density 870 kg/m³ -
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 140 - 160 °C -
Pré-secagem - tempo 4 - 6 h -
Umidade do processamento ≤0.02 % -
Temperatura da massa 390 - 400 °C -
Temperatura do molde 160 - 210 °C -
Zona 1 360 - 400 °C -
Características
Processamento
Moldagem por injeção
Forma de entrega
Granulos, Branco
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, America Centra e do Sul
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.