View Datasheet in other language

E-mail to a friend

Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Tisoplen® D 50D03 R01 - PP-GF50 - Tisan Engineering Plastics Co.Ltd.

Material Data Center offers the following functions for Tisoplen® D 50D03 R01:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Tisoplen datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:

Propriedades mecânicas - Propriedades térmicas - Propriedades elétricas - Outras propriedades - Recomendação de processamento Moldagem por injeção

Any use of this information falls under the rules of our disclaimer.

Propriedades mecânicas

Valor

Unidade

Método de ensaio

ISO Dados

Módulo de tração

7250

MPa

ISO 527

Tensão na ruptura

77.5

MPa

ISO 527

Deformação na ruptura

ISO 527

Impacto Izod com entalhe, +23°C

kJ/m²

ISO 180/1A

Propriedades térmicas

Valor

Unidade

Método de ensaio

ISO Dados

Temperatura de fusão, 10°C/min

163

°C

ISO 11357-1/-3

Temperatura de deflexão térmica, 1.80 MPa

145

°C

ISO 75-1/-2

Flamabilidade a 1.5mm esp. nom.

class

IEC 60695-11-10

Espessuras do tubo de teste

1.6

Flamabilidade a espessura h

class

IEC 60695-11-10

Espessuras do tubo de teste

0.8

Propriedades elétricas

Valor

Unidade

Método de ensaio

ISO Dados

Resistividade volumétrica específica

1E13

Ohm*m

IEC 62631-3-1

Resistividade superficial específica

1E15

Ohm

IEC 62631-3-2

Outras propriedades	Valor	Unidade	Método de ensaio
Densidade	1280	kg/m³	ISO 1183

Recomendação de processamento Moldagem por injeção	Valor	Unidade	Método de ensaio
Pré-secagem - temperatura	80	°C	-
Pré-secagem - tempo	1	h	-
Temperatura da massa	210 - 230	°C	-
Temperatura do molde	20 - 50	°C	-
Zona 1	150 - 180	°C	-
Zona 2	200 - 240	°C	-
Zona 3	200 - 240	°C	-
Temperatura do bico	230	°C	-
Contrapressão	0.3 - 2	MPa	-

Características

Processamento

Moldagem por injeção

Forma de entrega

Granulos, Cor natural

Disponibilidade regional

Europa, Oriente/África

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.