Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of UNIBRITE™ UB-830 - AEPDS - Nippon A&L Inc.

Material Data Center offers the following functions for UNIBRITE™ UB-830:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Unibrite datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 14 cm³/10min ISO 1133
Temperatura 220 °C -
Carga 10 kg -
Other Standards[S]
Contração após a moldagem, paralelo 0.5 % Producer Method
S: These properties are reported by the producer according standards that are different to our defaults.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Tensão no escoamento 51 MPa ISO 527
Módulo de flexão, 23°C 2450 MPa ISO 178
Resistência à flexão 83 MPa ISO 178
Res. impacto Charpy c/entalhe, +23°C 20 kJ/m² ISO 179/1eA
Dureza Rockwell R 114 - ISO 2039-2
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica, 1.80 MPa 89 °C ISO 75-1/-2
Coef. de expansão térmica linear, paralelo 76 E-6/K ISO 11359-1/-2
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1050 kg/m³ ISO 1183
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 85 - 95 °C -
Pré-secagem - tempo 3 - 6 h -
Temperatura da massa 220 - 280 °C -
Temperatura do molde 40 - 80 °C -
Características
Processamento
Moldagem por injeção
Características especiais
Estável contra o calor
Disponibilidade regional
Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.