Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Vampsulf 3028 V0 - PSU-GF30 - VAMP TECH SPA

Material Data Center offers the following functions for Vampsulf 3028 V0:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Vampsulf datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Resistência ao Impacto Izod, +23°C 20 kJ/m² ISO 180/1U
Impacto Izod com entalhe, +23°C 60 kJ/m² ISO 180/1A
ASTM Dados
Módulo de tração 9000 MPa ASTM D 638
Resistência à tração no escoamento 80 MPa ASTM D 638
Deformação na ruptura 1.2 % ASTM D 638
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Flamabilidade a 1.5mm esp. nom. V-0 class IEC 60695-11-10
Espessuras do tubo de teste 1.6 mm -
Flamabilidade a espessura h V-0 class IEC 60695-11-10
Espessuras do tubo de teste 3.2 mm -
ASTM Dados
DTUL @ 264 psi 175 °C ASTM D 648
Temperatura de amolecimento Vicat 185 °C ASTM D 1525
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1450 kg/m³ ASTM D 792
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 120 °C -
Pré-secagem - tempo 3 h -
Temperatura da massa 330 °C -
Temperatura do molde 120 °C -
Características
Processamento
Moldagem por injeção
Características especiais
Retardante de chama, Sem halogéneo
Certifications
RoHS
Disponibilidade regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.